همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۷
۰
۰
۰
۰

Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)

Harry Hardy's monorail sled from The Boy Mechanic, Book 2 (1915): two plank runners one behind the other under a 6 ft board, shod with square-edged strap iron that grips like a skate. The rider lies full length and steers the front runner with a bar, balancing like a cyclist.
متوسط
About 1 day

دستورالعمل‌ها

1

His sketch in centimetres

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic, Book 2

"Round iron or half-round iron should not be used, as these are liable to skid. The square, sharp edges of the strap iron prevent this and grip the surface just as a skate."
3

Cut and shoe the runners

Cut the two runners from 1 in plank to the size and shape of his sketch: the front runner 2 ft long, the rear one 2-1/2 ft long and about 1 ft high (the sketch prints the rear length with an inch mark; it is drawn as 2-1/2 ft). Shoe them with strap iron 1 in wide and 1/4 in thick, keeping the edges square and sharp.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
تسمه فولاد نرمتسمه فولاد نرم1 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
ارهٔ موییارهٔ مویی
ارهٔ آهن‌برارهٔ آهن‌بر
گیرهٔ رومیزیگیرهٔ رومیزی
دریل دستیدریل دستی
مدادمداد
متر نواریمتر نواری
4

Fit the rear runner

Nail or bolt blocks on either side of the upper edge of the rear runner and screw the top board (6 ft long, 1 in thick) to them. Brace the runner with strap iron, as in the sketch.

مواد مورد نیاز این مرحله:

تختهٔ کاجتختهٔ کاج1 قطعه
تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
تسمه فولاد نرمتسمه فولاد نرم1 قطعه
پیچ سرگرد گردن‌چهارگوشپیچ سرگرد گردن‌چهارگوش1 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
ارهٔ آهن‌برارهٔ آهن‌بر
دریل دستیدریل دستی
چکشچکش
5

Fit the front runner and steering

Fit the front runner the same way, but with only one pair of blocks at the centre and a thin piece of wood on their tops as the fifth wheel. Bore the hole for the steering post 6 in from the front end of the top, a little larger than the post. Round the post where it passes through the hole and leave its upper end square, to take the steering bar tightly.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
تسمه فولاد نرمتسمه فولاد نرم1 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
اسکنه‌هااسکنه‌ها
رندهٔ دستیرندهٔ دستی
6

Troubleshooting

Monorail sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Monorail Sled" by Harry Hardy, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 50). The rear runner length is printed 2-1/2 with an inch mark but drawn longer than the 2 ft front runner, so it is read here as 2-1/2 ft. He gives no sizes for the blocks, braces or steering bar. The tools and metric figures are ours.

مواد

5

ابزارهای لازم

11
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...