همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۱۲
۰
۰
۰
۰

Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)

A six-string guitar "having straight lines, giving it an old-fashioned appearance", from The Boy Mechanic (1913): a tapered box of hard maple with a seasoned soft-pine top, a drawknifed neck, frets cut from hatpins and a 24 in scale. Sizes are read on the 1913 scan. "If care is taken in selecting the material, and having it thoroughly seasoned, the finished instrument will have a fine tone."
پیشرفته
About 1 week, with glue drying

دستورالعمل‌ها

1

Cutting list and frets

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic

"The sides, ends and bottom are made of hard wood, preferably hard maple, and the top should be made of a thoroughly seasoned piece of soft pine." (J. H. Stoddard, Carbondale, Pa.)
3

Cut the pieces

Cut from thoroughly seasoned wood: top 3/16 by 14 by 17 in (soft pine); bottom 3/16 by 14 by 17 in, two sides 3/16 by 3-5/8 by 16-3/4 in, and ends 3/16 by 3-5/8 by 13-1/8 in and 9-5/8 in (hard maple); neck 1 by 2-5/16 by 18-1/2 in; fingerboard 3/16 by 2-5/8 by 16 in.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
تختهٔ کاجتختهٔ کاج1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
متر نواریمتر نواری
گونیای ثابتگونیای ثابت
4

Shape the neck and fingerboard

Taper the neck from G to F and from J to F, with the back rounded, using a drawknife: 2-3/8 in at the heel, 1-7/8 in at the nut F, and a head 2-3/4 in wide and 6-1/2 in long. Taper the fingerboard to match. Glue a piece of hard wood 1/4 in square and 1-7/8 in long across the neck at F as the nut. Glue the fingerboard to the neck and clamp it until the glue sets.

مواد مورد نیاز این مرحله:

نوارِ چوب سختنوارِ چوب سخت1 قطعه
چسب چوبچسب چوب1 قطعه

ابزارهای مورد نیاز:

کارد دودستهکارد دودسته
ارهٔ دستیارهٔ دستی
گیرهٔ میله‌ایگیرهٔ میله‌ای
5

Fret the fingerboard

Mark the frets from the nut using the computed positions in step 1 (fret 1 at 1.347 in, fret 12 at 12 in). His drawing gives only five spaces, 1-2/5, 1-3/16, 1-1/8, 1-1/16 and 1 in; added up they put the 5th fret about 0.3 in short of the true place, so they are shown for history only. Cut pieces from hatpins and fasten them across the fingerboard with small wire staples. Mark accurately: the frets decide the pitch.

مواد مورد نیاز این مرحله:

سنجاق کلاهسنجاق کلاه1 قطعه
منگنهٔ سیمیمنگنهٔ سیمی1 قطعه

ابزارهای مورد نیاز:

انبردست تختانبردست تخت
چکشچکش
متر نواریمتر نواری
گونیای ثابتگونیای ثابت
6

Build the box

Glue the sides and ends together, so the body is 10 in wide at the neck end, 13-1/2 in at the tail and 16-1/2 in long. Glue the front on, put heavy weights on top and give the glue time to dry. Fasten pieces of soft wood in the corners as braces, glue a small block C inside the neck end to take the bolt, and glue strips of soft wood K across the front and back to strengthen them. Cut the sound hole in the top as drawn.

مواد مورد نیاز این مرحله:

تیرک چوب نرمتیرک چوب نرم1 قطعه
چسب چوبچسب چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
گیرهٔ میله‌ایگیرهٔ میله‌ای
دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
7

Fit the neck

Make the brace D 1 in thick, to any shape you like. Glue the neck to the box and secure it with a carriage bolt at A through the end and block C. Glue the back on and smooth the outside with sandpaper.

مواد مورد نیاز این مرحله:

نوارِ چوب سختنوارِ چوب سخت1 قطعه
پیچ سرگرد گردن‌چهارگوشپیچ سرگرد گردن‌چهارگوش1 قطعه
تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
چسب چوبچسب چوب1 قطعه
کاغذ سنبادهکاغذ سنباده1 قطعه

ابزارهای مورد نیاز:

دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
گیرهٔ میله‌ایگیرهٔ میله‌ای
8

Make and place the bridge

Make the bridge 6 in long, 1 in wide and 3/8 in high, with an old hatpin or wire of the same size secured on top with pin staples as the saddle E. Drill six 3/16 in holes in it for the pins. Glue it on the top so the distance from the nut F to the saddle E is just 24 in.

مواد مورد نیاز این مرحله:

نوارِ چوب سختنوارِ چوب سخت1 قطعه
سنجاق کلاهسنجاق کلاه1 قطعه
منگنهٔ سیمیمنگنهٔ سیمی1 قطعه
چسب چوبچسب چوب1 قطعه

ابزارهای مورد نیاز:

دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
ارهٔ دستیارهٔ دستی
متر نواریمتر نواری
9

String it

Fit the turning pegs B in the head and string the guitar, holding the strings in the bridge with the pins. He bought the pegs and strings from a music store.

مواد مورد نیاز این مرحله:

گوشی کوکگوشی کوک1 قطعه
سیم گیتارسیم گیتار1 قطعه
پین خرک گیتارپین خرک گیتار1 قطعه

ابزارهای مورد نیاز:

دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
10

Troubleshooting

Guitar troubleshooting.

Flow

Loading...
11

History and honest limits

From **The Boy Mechanic**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913, p. 320, "A Guitar That Is Easy to Make", sent in by J. H. Stoddard of Carbondale, Pa.; sizes read on the 1913 scan (archive.org boymechanicthing01unse). He dimensions only the first five fret spaces, and they disagree with equal temperament; the fret positions used are computed by us. The sound hole, saddle and string tensions are not dimensioned. The tools and metric figures are ours.

مواد

12

ابزارهای لازم

8

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...