همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۹
۰
۰
۰
۰

Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)

William Cook of New York received US 710,762, dated 7 October 1902, for a Christmas tree stand of three leaning legs and three wire links. The links meet under the tree on a nail driven up into the butt, and their other ends are fixed part way up the legs. The tops of the legs are screwed to the trunk. The tree's weight pushes the feet out, the links pull back, and the tops of the legs squeeze the trunk. We make it from pine and steel wire. All sizes are ours.
مبتدی
About 3 hours

دستورالعمل‌ها

1

Where the links go

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 710,762

"The tendency of legs A to spread by weight of tree causes an outward tension at wire nail F through the several links C and inward pressure on stem of tree by upper part of legs A. Thus the tree is held very secure and perfectly upright by two opposite forces acting a short space apart and derived from weight of tree."
3

Cut the legs

Saw three legs 700 mm long from 70 x 22 mm pine (ours). Set a bevel gauge to 30 degrees and cut both ends of each leg at that angle, parallel to each other, so the foot sits flat on the floor and the top lies along the trunk, as in his Fig. 2. Sand off the splinters.

مواد مورد نیاز این مرحله:

تختهٔ کاجتختهٔ کاج1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
گونیای قابل تنظیمگونیای قابل تنظیم
متر نواریمتر نواری
مدادمداد
کاغذ سنبادهکاغذ سنباده
4

Bend the links

Cut three pieces of 2.5 mm steel wire, each the link length from the notebook plus about 60 mm for the eyes. Bend a round eye at each end with round-nose pliers, as his Fig. 3, so the eyes' centres are the link length apart. Make all three the same.

مواد مورد نیاز این مرحله:

مفتول فولادیمفتول فولادی3 قطعه

ابزارهای مورد نیاز:

سیم‌چینسیم‌چین
انبردست دم‌گردانبردست دم‌گرد
متر نواریمتر نواری
5

Staple the links to the legs

Mark each leg where the notebook says, on its inner face. Bend three U staples from the same wire (ours). Lay a link's outer eye on the mark and drive a staple over it into the leg, his staple H, leaving the eye free to turn.

مواد مورد نیاز این مرحله:

مفتول فولادیمفتول فولادی1 قطعه

ابزارهای مورد نیاز:

سیم‌چینسیم‌چین
انبردست دم‌گردانبردست دم‌گرد
چکش دوشاخچکش دوشاخ
6

Drill the tops of the legs

Drill a hole through the top of each leg, about 40 mm from its end, just big enough for the screw eye's shank to pass.

ابزارهای مورد نیاز:

دریل دستیدریل دستی
7

Nail the links to the butt

Saw the butt of the tree off square. Lay the tree on its side. Thread a long wire nail through the three free eyes of the links, his nail F, and drive it up into the middle of the bottom end of the tree.

مواد مورد نیاز این مرحله:

میخمیخ1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
چکش دوشاخچکش دوشاخ
8

Fix the tops of the legs

Bring the top of each leg in against the trunk. Make a start hole in the trunk with an awl through the leg's hole, and turn a screw eye through the leg into the trunk until the leg is held tight, his screw-eye D. Do all three, then stand the tree up.

مواد مورد نیاز این مرحله:

پیچ حلقه‌ایپیچ حلقه‌ای3 قطعه

ابزارهای مورد نیاز:

درفشدرفش
9

Check it stands upright

All three feet should touch the floor and the links should be straight and tight. Look at the tree from two sides. To take it down, turn out the screw eyes and pull the nail; the links fold about the nail for storing.
10

Troubleshooting

Christmas tree stand troubleshooting.

Flow

Loading...
11

History and honest limits

**William Cook** of New York, US 710,762, dated 7 October 1902, filed 29 July 1901. He claimed "a Christmas-tree stand composed of legs, and links, one end of each link being connected with one leg at a point intermediate between the ends of the leg, and the opposite ends of the links being connected with each other to form a seat". He says the stand is "more economical of construction and more easily applied" and that "size of tree offers no obstacle". He names no materials and gives no sizes: the pine, the wire, the 700 mm legs, the 30 degree angle, the butt height and how the screw eyes pass through the legs are ours. His drawing also marks parts E and G, which his text does not describe.

مواد

4
  • جایگزین
  • جایگزین
  • 1 قطعه
    جایگزین
  • جایگزین

ابزارهای لازم

10
  • جایگزین
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...