هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Cracked C4 Cut: Cracking-Still Gas Liquefied and Split in Four Columns at 200 psi (Eastman, Texas Co., US 2,014,724)
Charlie

ایجاد شده توسط

Charlie

29. اکتبر 2026DE
۱
۰
۰
۰
۰

Cracked C4 Cut: Cracking-Still Gas Liquefied and Split in Four Columns at 200 psi (Eastman, Texas Co., US 2,014,724)

The gas from a cracking still is a mixture of light hydrocarbons. Compress it, chill it until it liquefies, and run it through four columns in turn: each column sends one group off its top, and the fourth gives the butanes and butylenes together, the C4 cut. Result: a liquefied butane-butylene cut. Eastman does not give its composition. Source: Eastman, US 2,014,724 (1935). Not given: the cut's make-up, how the impurities are removed, the refrigerant. The gas from Burton's still is used here as the same kind of cracking-still gas. Extremely flammable gases under pressure. Picture drawn by Youblob.
متخصص
1 day

دستورالعمل‌ها

1

Clean the cracking-still gas

Take the gas from a cracking still, preferably after its gasoline has been separated and impurities such as hydrogen sulfide, carbon dioxide and water removed. Eastman does not say how they are removed.

مواد مورد نیاز این مرحله:

گاز کراکینگگاز کراکینگ1 as required

ابزارهای مورد نیاز:

کپسول گاز تحت فشارکپسول گاز تحت فشار
2

Compress and chill it until it liquefies

Compress the gas, then cool it far enough that it liquefies almost completely.

ابزارهای مورد نیاز:

کمپرسور گازکمپرسور گاز
ستون تقطیر برودتیستون تقطیر برودتی
فشارسنجفشارسنج
3

Take off methane and hydrogen, then the C2s

Run the liquid through a series of fractionating columns at about 200 lbs per square inch. Methane and hydrogen escape from the top of the first column, at about -100 °F; ethylene and ethane from the second, at about -25 °F. Eastman burns the methane and hydrogen as fuel in his cracking furnaces.

ابزارهای مورد نیاز:

ستون تقطیر برودتیستون تقطیر برودتی
فشارسنجفشارسنج
4

Take off propane and propylene

Propane and propylene leave the top of the third column, at about +100 °F.

ابزارهای مورد نیاز:

دیگ تقطیر جزءبه‌جزءدیگ تقطیر جزءبه‌جزء
فشارسنجفشارسنج
5

Take the butanes and butylenes from the fourth column

The butane and butylene come off the top of the fourth column, at about +200 °F under the same pressure. This is the C4 cut. Ours: condense it into pressure cylinders.

ابزارهای مورد نیاز:

دیگ تقطیر جزءبه‌جزءدیگ تقطیر جزءبه‌جزء
فشارسنجفشارسنج
کپسول گاز تحت فشارکپسول گاز تحت فشار

مواد

1
  • جایگزین

ابزارهای لازم

5

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...