همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنیها

DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)
A variable DC supply regulated by controlled rectifiers instead of a series transistor. Two of the four rectifiers in the bridge are silicon controlled rectifiers; how late in each half-cycle they are fired sets the output. A voltage bridge and a current bridge each make an error signal, an analog OR gate passes whichever is larger, and the supply crosses over automatically between holding the voltage and holding the current.
Result: a variable voltage / current regulated DC supply with automatic cross-over.
Source: K. Kupferberg and J. Ash (Forbro Design), US 3,305,763 (1967), Fig. 1. Unknown: component values and the firing-angle circuit. Picture: the patent drawing.
پیشرفته
Unknown
دستورالعملها
1
1
Build the controlled rectifier bridge
Build the controlled rectifier bridge
In a case, wire the cord through a switch and fuse to a transformer. Feed its secondary into a bridge of two ordinary rectifiers and two silicon controlled rectifiers. Smooth the negative output through a choke and a capacitor, then through a current-sensing resistor (with a second capacitor forming a further filter) to the negative output terminal; the positive goes straight to the positive terminal. Ours: the case, switch and fuse. Not given: the ratings.
مواد مورد نیاز این مرحله:
جعبهٔ آلومینیومی1 قطعه
سیم انعطافپذیر با دوشاخه1 قطعه
کلید اهرمی1 قطعه
فیوز1 قطعه
ترانسفورماتور کاهنده1 قطعه
دیود2 قطعه
تریستور (SCR)2 قطعه
چوک صافی1 قطعه
خازن الکترولیتی2 قطعه
پست اتصال2 output + and -ابزارهای مورد نیاز:
دریل دستی
مجموعه پیچگوشتی2
2
Build the two bridges
Build the two bridges
Current bridge: the sensing resistor, a reference Zener, a fixed resistor and the variable current-control resistor. Voltage bridge: the load across the output, the variable voltage-control resistor, a fixed resistor and a second reference Zener. Feed both Zeners from a small separate supply. Not given: the values, the Zener supply.
مواد مورد نیاز این مرحله:
دیود زنر2 قطعه
رئوستا2 voltage and current controls
مقاومت1 sensing and bridge resistorsابزارهای مورد نیاز:
هویه3
3
Build the control chain and use it
Build the control chain and use it
Invert the current bridge's error in a phase-reversing amplifier and feed it, with the voltage bridge's error, to an analog OR gate that passes the larger. Amplify the result and feed it to a firing-angle control circuit that fires the two controlled rectifiers' gates later or earlier in each half-cycle. In use, set the voltage and the current: for any load larger than the cross-over resistance (voltage setting divided by current setting) the supply holds the voltage, for a smaller one the current. Not given: the amplifier, OR-gate and firing circuits in this form.
مواد مورد نیاز این مرحله:
برد مدار چاپی1 قطعه
مجموعهٔ ترانزیستور1 amplifiers
ماده ناشناخته1 OR gate and firing-angle circuit
سیم لحیم1 as neededابزارهای مورد نیاز:
هویهمواد
17- 1 قطعهجایگزین
- جایگزین
- جایگزین
- 1 قطعهجایگزین
- 1 قطعهجایگزین
- 2 قطعهجایگزین
- 2 قطعهجایگزین
- 1 قطعهجایگزین
- 2 قطعهجایگزین
- جایگزین
- 2 قطعهجایگزین
- 2 voltage and current controlsجایگزین
- 1 sensing and bridge resistorsجایگزین
- 1 قطعهجایگزین
- 1 amplifiersجایگزین
- 1 OR gate and firing-angle circuitجایگزین
- 1 as neededجایگزین
این نقشه میسازد
نقشههای مرتبط
این نقشهها دانش مشترکی دارند — تکنیکها، مواد یا اصول
CC0 مالکیت عمومی
این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.
با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت میکند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

