همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۶
۰
۰
۰
۰

Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)

The smith's own top and bottom tools, from George Edwinson's farrier's chapter in Amateur Work (1886): an inch iron bar upset, split into a fork and a steel wedge welded in, then forged into a fuller, pritchel punch, curved or straight hot sett, or a square-tanged bottom sett; the pritchel itself from 1/2 in. square tool steel; handles of twisted iron rod or green withy.
پیشرفته
A day at the forge for the set

دستورالعمل‌ها

1

His proportions

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Edwinson

"To make this tool, heat and upset the end of an inch bar of iron; then heat again and split with a sett."
3

Split the iron

Heat and upset the end of a 1 in. (25 mm) iron bar. Heat again and split it with a hot set into a fork 1 to 1 1/4 in. long by 3/4 in. wide (his fig. 108).

مواد مورد نیاز این مرحله:

میلهٔ آهن چکش‌خوارمیلهٔ آهن چکش‌خوار1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
پتکپتک
قلم داغقلم داغ
انبر آهنگریانبر آهنگری
4

Weld in the steel

Heat the end of a steel bar of similar size and forge a wedge to fit the fork (fig. 109). Bring both to a welding heat and weld them well together.

مواد مورد نیاز این مرحله:

فولاد بوته‌ایفولاد بوته‌ای1 قطعه
پودر بوراکسپودر بوراکس1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
پتکپتک
انبر آهنگریانبر آهنگری
5

Forge the fuller

Cut off 2 in. of steel and 3 in. of iron for the tool. Forge the steel, with the iron behind it, into the fuller's rounded blade (fig. 102). Make the neck while it is still on the bar, then cut it off leaving a piece of iron for the head.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
قلم داغقلم داغ
6

Same blank, other tools

Pritchel punch: about 2 in. of iron and 1 in. of steel, shaped as fig. 103. Curved set: as the fuller but with a gouge-shaped blade (fig. 105). Top hot set: the same, with a chisel or wedge blade (fig. 106). Bottom set: a wedge of steel and iron, edge up, on a square tang that fits the anvil's square hole (fig. 107).

مواد مورد نیاز این مرحله:

میلهٔ آهن چکش‌خوارمیلهٔ آهن چکش‌خوار1 قطعه
فولاد بوته‌ایفولاد بوته‌ای1 قطعه
پودر بوراکسپودر بوراکس1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
پتکپتک
انبر آهنگریانبر آهنگری
7

Forge the pritchel

Forge 1/2 in. (13 mm) square tool steel into the tapered pritchel (fig. 104), 6 in. (150 mm) long. It punches nail holes in hot iron, so it need not be hardened.

مواد مورد نیاز این مرحله:

میلگرد فولاد ابزارمیلگرد فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
8

Fit the handles

Rod handle: twist 3/8 in. iron rod once round the neck and weld the two ends together (fig. 110). Withy handle: take a green or half-green hazel, willow, oak or withy rod about 3 ft long, twist the middle 8-9 in., wrap it once round the neck and bind the two ends with wire or a link (figs. 106, 111).

مواد مورد نیاز این مرحله:

میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 قطعه
ترکه‌های بید (نرم)ترکه‌های بید (نرم)1 قطعه
سیم آهنیسیم آهنی1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
9

Harden the cutting tools (ours)

He gives no temper for these. Ours: harden and temper the set edges as for other hot-cutting tools, and cool them often in use.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سطل آب‌دهیسطل آب‌دهی
10

Troubleshooting

Top-tool troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" VII, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 14-16 and figs. 101-111 (checked on the archive.org scan amateurworkillus06lond). He calls the top hot cutter a "sett"; we map it to the Hot Chisel head and the bottom sett to the Hot Cut Hardy head. Temper, metric figures and tools are ours.

مواد

7

ابزارهای لازم

7

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...