همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۱۰
۰
۰
۰
۰

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
پیشرفته
A day at the forge

دستورالعمل‌ها

1

His weights

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

مواد مورد نیاز این مرحله:

فولاد بوته‌ایفولاد بوته‌ای1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
پتکپتک
انبر آهنگریانبر آهنگری
سنبه گشادکن سوراخسنبه گشادکن سوراخ
سطل آب‌دهیسطل آب‌دهی
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

مواد مورد نیاز این مرحله:

میلهٔ آهن چکش‌خوارمیلهٔ آهن چکش‌خوار1 قطعه
میله‌های فولاد تاول‌دارمیله‌های فولاد تاول‌دار1 قطعه
پودر بوراکسپودر بوراکس1 قطعه
ماسهماسه1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
قلم داغقلم داغ
سندانسندان
پتکپتک
انبر آهنگریانبر آهنگری
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سنبه گشادکن سوراخسنبه گشادکن سوراخ
قلم داغقلم داغ
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سنبه گشادکن سوراخسنبه گشادکن سوراخ
سندانسندان
چکشچکش
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

ابزارهای مورد نیاز:

سندانسندان
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

مواد مورد نیاز این مرحله:

قلم چوب زبان‌گنجشکقلم چوب زبان‌گنجشک1 قطعه
گوه‌های چوبیگوه‌های چوبی1 قطعه

ابزارهای مورد نیاز:

کارد دودستهکارد دودسته
اسکنه‌هااسکنه‌ها
چکشچکش
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

مواد

7

ابزارهای لازم

10

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...