همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)
Volt

ایجاد شده توسط

Volt

14. نوامبر 2026SE
۹
۰
۰
۰
۰

Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)

The Victorian battery terminal, from George Edwinson's Electro-plating at Home (Amateur Work, 1881): a brass body turned from 1 1/2 in. of 5/8 in. rod, slotted for the plate and bored for the wire, with thumb screws turned from 3/8 in. rod; or a clamp bent hot from a brass strip with a soldered-on wire piece.
متوسط
Two hours at the lathe

دستورالعمل‌ها

1

His sizes

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Edwinson

"Those who may have lathes ... may easily turn up a binding-screw ... out of a 1 1/2 in. length of 5/8 in. brass rod."
3

Turn the body

Cut 1 1/2 in. (38 mm) of 5/8 in. (16 mm) brass rod and turn the body to shape first (his fig. 3: a round head on a tapering neck over a forked foot).

مواد مورد نیاز این مرحله:

میلگرد برنجیمیلگرد برنجی1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
تراش فلزتراش فلز
رندهٔ برش تراشرندهٔ برش تراش
4

Slot and bore

Cut the slot that grips the plate. Bore a hole for the wire through the head, then bore the holes for the screws.

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
ارهٔ آهن‌برارهٔ آهن‌بر
سوهان (سوهان دستی)سوهان (سوهان دستی)
دریل دستیدریل دستی
5

Turn the thumb screws

Turn the screws from 3/8 in. (9.5 mm) brass rod with plain thumb-screw heads (he says milled heads are a mistake). Cut a fine thread on them and tap the holes to match.

مواد مورد نیاز این مرحله:

میلگرد برنجیمیلگرد برنجی1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
رندهٔ برش تراشرندهٔ برش تراش
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
6

Bent clamp (variant)

From good malleable brass take a strip 3 in. long, 1/2 in. wide and 1/4 in. thick (76 x 13 x 6 mm). Heat it to a dull red and bend it over a former of hot iron. Cut the piece for the wire and centre screw separately, hard-solder it on and trim it. Fit thumb screws as above. (A clamp may also be cast from a wooden pattern.)

مواد مورد نیاز این مرحله:

نوار برنجینوار برنجی1 قطعه
لحیم نقرهلحیم نقره1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
انبر آهنگریانبر آهنگری
چکشچکش
مشعل لحیم‌کاری سختمشعل لحیم‌کاری سخت
سوهان (سوهان دستی)سوهان (سوهان دستی)
دریل دستیدریل دستی
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
7

Clean and keep it working

Clean the slot with folded emery cloth and the wire hole with the tang of a file. Now and then oil the screw, work it in and out, and wipe the oil off. Do not screw up too tight.

ابزارهای مورد نیاز:

سوهان (سوهان دستی)سوهان (سوهان دستی)
8

Troubleshooting

Binding-screw troubleshooting.

Flow

Loading...
9

History and honest limits

From George Edwinson, "Electro-plating at Home", **Amateur Work, Illustrated**, vol. I (1881), p. 81 figs. 3 and 7 and p. 99 (checked on the archive.org scan amateurworkillus11881lond). He gives no thread size. Modern panel binding posts add an insulating bush and a banana-plug socket; this is the 1881 brass terminal. The metric figures and the tools are ours.

مواد

3

ابزارهای لازم

11

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...