همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Forged Lathe Tools: Narrow Cutting-Off Tool and Bent-Tip Inside Boring Tool, Ground to Rake and Clearance (Griswold, 1904)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۷
۰
۰
۰
۰

Forged Lathe Tools: Narrow Cutting-Off Tool and Bent-Tip Inside Boring Tool, Ground to Rake and Clearance (Griswold, 1904)

Two of the forged lathe tools in Robert Gibson Griswold's Tool Making for Amateurs (Boston, 1904): a cutting-off (parting) tool deep under a very narrow edge with relieved sides and a chip-splitting groove, and an inside boring and threading tool drawn to a long taper with the tip bent left; both ground to 3-5 degree clearance and the rake suited to the metal.
پیشرفته
Half a day per tool

دستورالعمل‌ها

1

His angles

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Griswold

"The writer uses a tool slightly less than 1-16 in. wide and 1 in. deep for short cuts."
3

Forge the cutting-off tool

Forge tool steel (stock size ours, to suit your tool post) into a blade deep under the cutting edge, with the point the widest part and the sides relieved behind it so it cannot bind (his fig. 18): slightly under 1/16 in. wide and 1 in. deep for work up to 1/2 in., about 3/32 in. wide for work up to 2 in.

مواد مورد نیاز این مرحله:

میلگرد فولاد ابزارمیلگرد فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
4

Forge the boring tools

Draw three blanks to a long tapering end and bend the extreme tip to the left (fig. 23).

مواد مورد نیاز این مرحله:

میلگرد فولاد ابزارمیلگرد فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
5

Harden and temper

Carbon tool steel: harden the ends (ours: cherry red into water) and temper in the yellows. Self-hardening steel must never be quenched in water.

مواد مورد نیاز این مرحله:

آبآب1 قطعه
پارچهٔ سنبادهپارچهٔ سنباده1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سطلسطل
6

Grind the cutting-off tool

Give it front and side clearance of 3-5 degrees and little top rake. For larger work grind a round groove in the facing edge so the chip splits into two strings.

ابزارهای مورد نیاز:

سنگ‌سنبادهٔ رومیزیسنگ‌سنبادهٔ رومیزی
7

Grind the boring points

Grind one boring tool as a diamond point, one as a small square point that works into corners, and one as a 60 degree thread point. Rake 3-10 degrees for iron and steel, little or none for brass and copper; hone the edges.

ابزارهای مورد نیاز:

سنگ‌سنبادهٔ رومیزیسنگ‌سنبادهٔ رومیزی
سنگ تیزکنیسنگ تیزکنی
8

Troubleshooting

Lathe tool troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" IV, **Amateur Work** (Boston), vol. IV (1904-05), pp. 23-26 and figs. 11-25 (checked on the archive.org scan amateurwork04bostrich). He shows a full set (diamond point, side, round-nose, thread, centering, brass tools); this blueprint makes the two our heads need. Stock size and quench are ours.

مواد

3

ابزارهای لازم

7

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...