همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۹
۰
۰
۰
۰

Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)

The simplest home-made taper reamer, from Robert Gibson Griswold's Tool Making for Amateurs (Boston, 1905): tool steel turned to the taper wanted (his was 1/8 in. per foot), one side filed away exactly to the centre line so that two cutting edges remain, then hardened and ground on the flat face only. It reams a very smooth conical hole.
متوسط
Two to three hours

دستورالعمل‌ها

1

His taper

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Griswold

"Turn a piece of tool steel to the proper taper and then file away one side until the flat surface coincides with the center line."
3

Turn the taper

Turn a piece of tool steel in the lathe to the taper of the part the hole must fit (his: 1/8 in. per foot). Length and diameter are ours: a little longer than the hole and spanning its two diameters.

مواد مورد نیاز این مرحله:

میلگرد فولاد ابزارمیلگرد فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
کولیسکولیس
4

File to the centre line

Hold it in the vice and file away one side until the flat face lies exactly on the centre line. This leaves a cutting edge on each side.

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
سوهان (سوهان دستی)سوهان (سوهان دستی)
کولیسکولیس
5

Harden and grind

Harden it (ours: heat to a cherry red and quench in water, temper to a straw colour), then grind on the flat side only, never on the round.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سطل آب‌دهیسطل آب‌دهی
سنگ‌سنبادهٔ رومیزیسنگ‌سنبادهٔ رومیزی
6

Troubleshooting

Reamer troubleshooting.

Flow

Loading...
7

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" VII, **Amateur Work** (Boston), vol. IV (1904-05), p. 128 (checked on the archive.org scan amateurwork04bostrich). He gives no size or temper for the reamer; those and the tools are ours. He finishes the hardened bushings with a copper lap and emery.

مواد

1

ابزارهای لازم

7

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...