همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۱۱
۰
۰
۰
۰

Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)

Marselius J. Logan of Springfield, Virginia, received US 1,377,495, dated 10 May 1921. Three knives sit in grooves along a conical head, their bevelled edges just proud of the cone. A collar screwed along the shank pushes all their back ends at once, so each cuts the same share. When they wear, a turn of the collar sets them out again. Set screws lock them. A stop pin beside them halts every countersink at the same depth. The patent gives no sizes; every size here is ours.
پیشرفته
About 2 days

دستورالعمل‌ها

1

Setting the knives out evenly

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 1,377,495

"All of the cutters or knives 10 are made alike in length as well as other dimensions, so that by screwing the collar 7 into contact with the inner ends 12 of all of said cutters, the latter may be evenly adjusted to cut equally, and when their cutting edges 11 become worn down said cutters may be uniformly projected in order to provide the proper clearance."
3

Turn the inner member 1 and the sleeve 4

From 30 mm steel bar turn the inner member: a 90 degree cone 3 26 mm across at its base, a short cylindrical edge under it, and a shank 2 14 mm across, threaded M14 for 20 mm below the head 6 and plain below. From 40 mm bar turn the sleeve: a ring bored 0.03 mm under the head's edge, with a flange 5 30 mm long bored 22 mm, so it leaves an annular space 13 round the shank. Heat the sleeve to 250 C in the oven and drop it over the head's edge; let it cool.

مواد مورد نیاز این مرحله:

میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم2 قطعه
روغن برشروغن برش1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
میلهٔ بورینگمیلهٔ بورینگ
رندهٔ برش تراشرندهٔ برش تراش
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
فرفر
دستکش جوشکاریدستکش جوشکاری
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
عینک ایمنیعینک ایمنی
4

Grooves, knives and screws

Saw and file three grooves 4 mm square, parallel to the axis, a third of the way round from each other, through the joint of head and sleeve and on into the annular space. File the cone away 14 ahead of each groove for the shavings. Cut three knives 32 mm long from 4 mm square tool steel, exactly alike, and grind each one's top end to the cone's slope with a bevelled cutting edge 11. Harden them (cherry red, water, temper to light straw). Drill and tap M4 through the sleeve over each groove for the set screws 15. Make a collar 7 with an M14 thread to screw up the shank inside the flange, and an M4 set screw 19 to lock it. Drill and tap M5 into the head's edge behind one knife for the stop pin 16, with an M4 set screw 18 to lock it.

مواد مورد نیاز این مرحله:

میلهٔ چهارگوش فولاد ابزارمیلهٔ چهارگوش فولاد ابزار1 قطعه
میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 قطعه
پیچ خارِ سرگودپیچ خارِ سرگود5 قطعه
پیچ آلن سرتخت‌استوانه‌ایپیچ آلن سرتخت‌استوانه‌ای1 قطعه
مهرهٔ شش‌گوشمهرهٔ شش‌گوش1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
مجموعه سوهانمجموعه سوهان
گیرهٔ رومیزیگیرهٔ رومیزی
سنگ‌سنبادهٔ رومیزیسنگ‌سنبادهٔ رومیزی
کورهٔ آهنگریکورهٔ آهنگری
انبر آهنگریانبر آهنگری
آهن‌ربای کوچکآهن‌ربای کوچک
سطل آب‌دهیسطل آب‌دهی
آبآب
سنگ تیزکنیسنگ تیزکنی
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
دسته قلاویزدسته قلاویز
تراش فلزتراش فلز
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
5

Set, lock and countersink

Slide the knives into their grooves, back ends down in the annular space. Screw the collar up until all three knives' edges stand 0.3 mm out of the cone, and lock it and the knives. Set the stop pin so it touches the work when the countersink is the size wanted, and lock it. Countersink a row of screw holes in hardwood: every one should come out the same.

ابزارهای مورد نیاز:

مجموعه آچار آلنمجموعه آچار آلن
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
تختهٔ چوب سختتختهٔ چوب سخت
عینک ایمنیعینک ایمنی
6

Troubleshooting

Adjustable-knife countersink troubleshooting.

Flow

Loading...
7

History and honest limits

**Marselius J. Logan** of Springfield, Virginia, assignor of one-half to Laurence G. Alexander of Alexandria, Virginia, US 1,377,495, dated 10 May 1921, filed 14 February 1920. He claimed "a flange carried by the head and extending concentrically along the shank in spaced relation thereto, cutters mounted on the head and extending into the space between the same and the flange, and a collar adjustable on the shank within said flange for alining the cutters", and "an adjustable stop". He shows three knives; ours too. He gives no sizes; every size here is ours.

مواد

6

ابزارهای لازم

26

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...