همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۹
۰
۰
۰
۰

Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)

James H. Reinhardt of East Orange, New Jersey, received US 1,261,438, dated 2 April 1918, for a profile gauge: a row of pins clamped between two thin metal members. Rubber tubes wrapped in cloth press on the pins, so each one slides when pushed and stays where it is left. Pressed against an object, the pin ends take its outline, and a pencil drawn along them copies it, so the shape can be made again. We build his single gauge from brass sheet and steel wire. All sizes are ours.
متوسط
About 5 hours

دستورالعمل‌ها

1

How many pins

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 1,261,438

"The rods or pins 3 of the respective gages may be pushed against the surface of the object, as required, to obtain its outline along the ends of the rods or pins, whereby a pencil may be drawn along the ends of the pins to trace such outline or contour of the object. From such outlines objects corresponding to the master object may be reproduced either in relief or concave according to which way the outline drawn from the ends of the rods is used."
3

Make the two members

Cut two strips of 0.8 mm brass sheet 200 x 32 mm (ours) with tin snips and file the edges. Bend 4 mm down along each long side in the vice, so each strip becomes a shallow channel 24 mm wide: his "gutter-like form". Clamp them together, open sides facing, and drill a 3.5 mm hole through both, 50 mm from each end, on the middle line.

مواد مورد نیاز این مرحله:

ورق برنجورق برنج2 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
مجموعه سوهانمجموعه سوهان
گیرهٔ رومیزیگیرهٔ رومیزی
سوزن خط‌اندازسوزن خط‌انداز
دریل دستیدریل دستی
4

Make the gutters

Cut two strips of the same brass 180 x 14 mm and bend each round a 6 mm rod into a U that will hold the rubber tube, his gutters 10. Rivet them inside one member, one near each long side, with copper rivets, keeping clear of the screw holes.

مواد مورد نیاز این مرحله:

ورق برنجورق برنج1 قطعه
پرچ مسیپرچ مسی6 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
میلگرد فولاد نرممیلگرد فولاد نرم
گیرهٔ رومیزیگیرهٔ رومیزی
دریل دستیدریل دستی
چکش گِرد‌سرچکش گِرد‌سر
5

Make the retainers

Cut two pieces of 6 mm rubber tubing 170 mm long and push a 2 mm wire through each, his cores 9, "to somewhat stiffen them". Wrap each in a strip of cotton cloth, lap its edges and glue them with contact cement, his protecting cloth 12, so the rubber does not touch the metal. Lay one in each gutter.

مواد مورد نیاز این مرحله:

شیلنگ لاستیکیشیلنگ لاستیکی1 قطعه
مفتول فولادیمفتول فولادی1 قطعه
پارچهٔ پنبه‌ایپارچهٔ پنبه‌ای1 قطعه
چسب تماسیچسب تماسی1 قطعه

ابزارهای مورد نیاز:

سیم‌چینسیم‌چین
قیچیقیچی
6

Cut the pins

Cut 1 mm steel wire into pins 120 mm long, as many as the notebook gives. Straighten any that are bent and file both ends flat and smooth, so they slide easily and do not mark the work.

مواد مورد نیاز این مرحله:

مفتول فولادیمفتول فولادی1 قطعه

ابزارهای مورد نیاز:

سیم‌چینسیم‌چین
مجموعه سوهان سوزنیمجموعه سوهان سوزنی
گیرهٔ رومیزیگیرهٔ رومیزی
7

Assemble

Lay the member with the retainers open side up. Lay the pins across it side by side, touching, centred so equal lengths stick out on both sides; leave a gap at each screw hole (ours). Put the other member on top and pass a machine screw through each hole with a nut. Tighten them evenly until each pin slides when pushed but does not fall.

مواد مورد نیاز این مرحله:

پیچ‌های ماشینیپیچ‌های ماشینی2 قطعه
مهرهٔ شش‌گوشمهرهٔ شش‌گوش2 قطعه

ابزارهای مورد نیاز:

مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
آچار فرانسهآچار فرانسه
8

Take a profile

Push all the pins level with a flat board. Press the gauge square against the object until the pins have taken its shape. Lift it off, lay it on paper or on the stock to be cut, and draw a pencil along the pin ends.

ابزارهای مورد نیاز:

مدادمداد
9

Troubleshooting

Pin profile gauge troubleshooting.

Flow

Loading...
10

History and honest limits

**James H. Reinhardt** of East Orange, New Jersey, US 1,261,438, dated 2 April 1918, filed 20 June 1914. He claimed "a profile gage comprising a pair of opposed members, rods or pins located between and transversely with respect to said members, means for clamping said members together" and "a resilient retainer comprising spaced rubber tubes". His members can have teeth along their edges, and his patent also covers end castings that join several gauges in a line or at an angle, a smaller gauge clamped between them, a toothed spacer strip and a rubber-mat retainer: none of those are built here. He gives no sizes: the brass, the 200 mm length, the 1 mm pins, the tube and core sizes, the cement, the rivets and the screws are ours.

مواد

8

ابزارهای لازم

13

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...