همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۱۱
۰
۰
۰
۰

Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)

Howard S. Root of Spokane received US 2,631,224, dated 10 March 1953, for a safe light for jack-o'-lanterns: "The most common device is an ordinary candle. That, however, is very dangerous." A springy tin clip holds a dry cell; a bulb screwed into a hinged tin support rests on the top of the cell, and the clip itself carries the current back from the bottom. A wire handle through the lid lifts the bulb to switch it off. We bend it from tinplate and fit it in a carved pumpkin. All sizes are ours.
مبتدی
About 2 hours

دستورالعمل‌ها

1

Bracket blank

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 2,631,224

"I provide an operating means for the light bulb support 18 of such a nature that the child can turn the light on and off at will, yet if the entire toy is carried by the operating handle, no harm is done to the device."
3

Bend the cell clip

Cut the tinplate strip from the notebook. Bend it into a U round the cell, his container 10: the bottom is the cross bar 10c, the sides are legs 10a and 10b. Curve the legs a little across their width so the cell cannot slide out sideways, and snip and press in a small tongue on each leg (his 15) to grip it. Snip two pointed fingers at the bottom (his 13).

مواد مورد نیاز این مرحله:

ورق حلبیورق حلبی1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
انبردست تختانبردست تخت
4

Make the bulb support

Cut a tin plate a little longer than the cell is wide, his support 18. Punch a hole in the middle just big enough for the bulb's screw base to screw into (his threaded aperture 19; ours). Bend two small ears at the top of leg 10a (his 21) and roll the support's end round a wire pin (22) between them, so it hinges.

مواد مورد نیاز این مرحله:

ورق حلبیورق حلبی1 قطعه
سیم فولاد فنرسیم فولاد فنر1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
سنبهٔ نشانه‌گذاریسنبهٔ نشانه‌گذاری
انبردست دم‌گردانبردست دم‌گرد
انبردست تختانبردست تخت
5

Fit the spring and handle

Wind a few turns of spring wire on the hinge pin, one end hooked over the top of leg 10a and the other over the support, so it presses the support down (his spring 25). Bend a wire handle (his 20) long enough to come out of the top opening; pivot its lower end in a turned-over tab on leg 10b (26) and bend a short arm (27) under the free end of the support, so raising the handle lifts the bulb.

مواد مورد نیاز این مرحله:

سیم فولاد فنرسیم فولاد فنر1 قطعه

ابزارهای مورد نیاز:

انبردست دم‌گردانبردست دم‌گرد
انبردست تختانبردست تخت
سیم‌چینسیم‌چین
6

Put in the cell and bulb

Seat the cell with its centre terminal down on the cross bar, put a tin band (his 16) round the legs if they are loose, and screw the bulb into the support. Let the support down: the bulb's end terminal should touch the top of the cell and light, the current returning through the support, the hinge and the clip.

مواد مورد نیاز این مرحله:

پیل خشکپیل خشک1 قطعه
لامپ چراغ‌قوهلامپ چراغ‌قوه1 قطعه
ورق حلبیورق حلبی1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
انبردست تختانبردست تخت
7

Fit it in the pumpkin

Carve the pumpkin's face and cut the top opening (ours; his toys are hollow figures). Push the clip's fingers through the bottom of the pumpkin, put a washer over them outside, and bend them over it (his washer 8), so the light stands in the middle. Pass the handle up through the top opening.

مواد مورد نیاز این مرحله:

کدو تنبلکدو تنبل1 قطعه
واشر تختواشر تخت1 قطعه

ابزارهای مورد نیاز:

چاقوی کاردستیچاقوی کاردستی
انبردست تختانبردست تخت
8

Use it

Lower the handle and the bulb lights; raise it and the light goes off. To change the cell, lift the support and take the cell out.
9

Troubleshooting

Jack-o'-lantern light troubleshooting.

Flow

Loading...
10

History and honest limits

**Howard S. Root** of Spokane, Washington, US 2,631,224, dated 10 March 1953, filed 21 December 1948. He claimed "an illuminated figure toy comprising a hollow body having an opening in the top thereof", a conductive container for a dry cell, a hinged conductive bulb support, and spring means pressing the bulb's end terminal against the cell. He also shows other hinges, a magnet latch and a side handle (Figs. 6-13), not built here. He gives no sizes or materials: the tinplate, all sizes, the pumpkin and the cell and bulb are ours.

مواد

6
  • 3 قطعه
    جایگزین
  • جایگزین
  • 1 قطعه
    جایگزین
  • جایگزین
  • 1 قطعه
    جایگزین
  • 1 قطعه
    جایگزین

ابزارهای لازم

6

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...