همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۱۱
۰
۰
۰
۰

Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)

Albert G. Sewell received US 1,674,999, dated 26 June 1928, for a soft-face hammer whose worn faces can be renewed instead of throwing the hammer away. Each end of the head is a cup. A face rolled from a strip is pressed into the cup onto a loose sheet-metal disc whose prongs bite into it and wedge it tight. When a face is battered, a rod pushed through a notch at the bottom of the cup drives the disc and the face out together, and a new face goes in. He preferred rawhide and named rubber among face materials; ours are rolled from rubber sheet. The patent gives no sizes; every size here is ours.
متوسط
About 1 day

دستورالعمل‌ها

1

Rolling a face plug

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 1,674,999

"Thus, by hammering or otherwise thrusting a rod or suitable device against the wedging member, the latter, with the striking face member, can be forced or driven out of the socket or recess, after which a new striking face member may be forced into the socket, to be secured therein by the wedging member."
3

Turn the head

Grip 40 mm steel round bar in the chuck and turn a head 110 mm long: the two ends stay 40 mm across for 26 mm as the flanges D, and the middle is waisted to 30 mm. Bore each end 32 mm across and 22 mm deep for the sockets C, flat at the bottom. Drill a 20 mm eye B through the middle, square to the axis, in a V-block on the drill press.

مواد مورد نیاز این مرحله:

میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 قطعه
روغن برشروغن برش1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
میلهٔ بورینگمیلهٔ بورینگ
رندهٔ برش تراشرندهٔ برش تراش
دریل ستونیدریل ستونی
بلوک V‌شکلبلوک V‌شکل
مجموعه متهمجموعه مته
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
عینک ایمنیعینک ایمنی
4

Cut the notches K

On the handle's side of each flange, saw and file a notch 8 mm wide through the flange's wall at the very bottom of the socket, so a rod can be pushed in at a slant against the edge of the disc at the bottom.

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
ارهٔ آهن‌برارهٔ آهن‌بر
مجموعه سوهانمجموعه سوهان
سنبهٔ نشانه‌گذاریسنبهٔ نشانه‌گذاری
5

Pronged discs G

Cut two discs of 1.5 mm steel sheet 31.5 mm across. At four places round each rim, snip two cuts 6 mm deep 5 mm apart and bend the tab between them up at a right angle with the pliers: the prongs H. Drop one disc loosely into the bottom of each socket, prongs out.

مواد مورد نیاز این مرحله:

ورق فولاد نرمورق فولاد نرم1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
انبردست تختانبردست تخت
گیرهٔ رومیزیگیرهٔ رومیزی
مجموعه سوهانمجموعه سوهان
6

Roll and press in the faces E

Cut two strips of 3 mm natural rubber sheet 32 mm wide and about 270 mm long. Roll each tightly into a coil, trimming the strip until the coil just enters a socket, and tie it. Press the coil into its socket in the vice, between soft packing, until it bottoms on the disc and its prongs bite in, leaving the face standing about 10 mm out. Cut the tie and trim the face flat with the knife.

مواد مورد نیاز این مرحله:

ورق لاستیک طبیعیورق لاستیک طبیعی1 قطعه

ابزارهای مورد نیاز:

چاقوی کاردستیچاقوی کاردستی
گیرهٔ رومیزیگیرهٔ رومیزی
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
7

Handle

Turn an ash handle 300 mm long, its end a tight fit in the eye. Saw a slot down its end, drive it into the eye, and glue and drive a hardwood wedge into the slot; saw it off flush.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
چسب چوبچسب چوب1 قطعه

ابزارهای مورد نیاز:

تراش چوبتراش چوب
ست ابزار تراش (HSS)ست ابزار تراش (HSS)
ارهٔ آهن‌برارهٔ آهن‌بر
چکش گِرد‌سرچکش گِرد‌سر
8

Renew a face

When a face is worn, push a steel rod through the socket's notch against the disc's edge and tap it out with the hammer; the disc and the face come out together. Put the disc back, prongs out, and press in a new rolled face.

ابزارهای مورد نیاز:

چکش گِرد‌سرچکش گِرد‌سر
گیرهٔ رومیزیگیرهٔ رومیزی
9

Troubleshooting

Soft-face hammer troubleshooting.

Flow

Loading...
10

History and honest limits

**Albert G. Sewell**, US 1,674,999, dated 26 June 1928, filed 25 July 1927. He describes a head with a socket at each end formed by annular flanges, a striking face member of relatively soft material rolled from a strip and pressed in as a plug, a loose sheet-metal wedging disc with prongs in the socket's bottom, and openings through which a rod drives the disc and face out. He preferred rawhide and his head was cast iron; ours is turned steel with faces rolled from rubber sheet, which he lists among the face materials in use. He gives no sizes; every size here is ours.

مواد

6

ابزارهای لازم

20

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...