همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

ایجاد شده توسط

Forge

15. نوامبر 2026NO
۵
۰
۰
۰
۰

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
مبتدی
An hour

دستورالعمل‌ها

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

مواد مورد نیاز این مرحله:

لوله برنجیلوله برنجی1 قطعه

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
ارهٔ آهن‌برارهٔ آهن‌بر
سوهان (سوهان دستی)سوهان (سوهان دستی)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
سوهان (سوهان دستی)سوهان (سوهان دستی)
سوهان‌های سوزنیسوهان‌های سوزنی
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

مواد مورد نیاز این مرحله:

ورق برنجورق برنج1 قطعه
سیم لحیمسیم لحیم1 قطعه
فلاکس لحیمفلاکس لحیم1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
هویههویه
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

مواد مورد نیاز این مرحله:

مفتول فولادیمفتول فولادی1 قطعه

ابزارهای مورد نیاز:

دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
سوهان (سوهان دستی)سوهان (سوهان دستی)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

مواد

5
  • جایگزین
  • 1 قطعه
    جایگزین
  • 1 قطعه
    جایگزین
  • جایگزین
  • جایگزین

ابزارهای لازم

8

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...