همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)
Forge

ایجاد شده توسط

Forge

15. نوامبر 2026NO
۵
۰
۰
۰
۰

Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)

The crushing rolls that took ore from the jaw breaker in a 1900s mill, as Robert Richards described them: two shafts on one cast-iron frame, each carrying a soft-iron core with a replaceable hard shell; one runs in fixed boxes, the other in movable boxes pushed toward it by a nest of steel springs that yields like a safety valve; shims set the gap. Little fines, ideal for soft brittle ores.
پیشرفته
Weeks (castings and machining)

دستورالعمل‌ها

1

His figures

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Richards

"The ore is therefore broken by compression."
3

Frame and shafts

Cast the frame as one piece, both sides joined by end pieces, so settling of the building can't throw the shafts out of line (make it in two parts only if it must travel by mule). Turn two shafts of mild steel or wrought iron, each on two bearings.

مواد مورد نیاز این مرحله:

قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه
محور فولادیمحور فولادی1 قطعه

ابزارهای مورد نیاز:

ملاقهٔ ریخته‌گریملاقهٔ ریخته‌گری
تراش فلزتراش فلز
قرقرهٔ مرکبقرقرهٔ مرکب
4

Cores and shells

Force a soft cast-iron core onto each shaft. Krom's way (Fig. 37): two slightly conical half-cores, one shrunk on for good, the other split on one side and drawn in by four draw bolts; half-cores no wider than 4-5 in. Cast hard shells 2-5½ in. thick (chilled iron or steel), with wrought-iron staves cast in if chilled so the slightly conical inside can be turned to fit; turn the face true.

مواد مورد نیاز این مرحله:

قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه
میلهٔ آهن چکش‌خوارمیلهٔ آهن چکش‌خوار1 قطعه
مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
ملاقهٔ ریخته‌گریملاقهٔ ریخته‌گری
5

Boxes, springs and shims

Mount one shaft in fixed boxes and the other in movable ones, both babbitted, with shields and a cotton-waste groove against grit. Put a nest of steel spiral springs outside the fixed pillow block, with bolts carrying the force to the movable box, equal on both sides, compressed between plates by two compression bolts. Set the gap with shims and keep them in: the springs should only give when a hard lump comes through.

مواد مورد نیاز این مرحله:

Coil SpringCoil Spring1 قطعه
فلز نامعلومفلز نامعلوم1 قطعه
مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش1 قطعه
قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه

ابزارهای مورد نیاز:

مجموعهٔ آچار تختمجموعهٔ آچار تخت
تراش فلزتراش فلز
6

Drive and run

Drive by belt and pulley (or gears and pulleys for slow coarse work). Feed lumps no bigger than about 1½ in. (4 cm), 2½ in. at most, evenly with a feeder so a rush of ore does not choke it.

مواد مورد نیاز این مرحله:

قرقرهقرقره1 قطعه
تسمهٔ انتقال نیروتسمهٔ انتقال نیرو1 قطعه

ابزارهای مورد نیاز:

مجموعهٔ آچار تختمجموعهٔ آچار تخت
7

Troubleshooting

Crushing rolls troubleshooting.

Flow

Loading...
8

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter III, §§ 71-85, pp. 62-74, Fig. 37 and Tables 34-39 (checked on the archive.org scan oredressing01richuoft; p. 62 from its text layer). Rubber springs were the cheap short-life option; levers and weights had nearly gone out of use. Richards surveys machines from many makers rather than one design: building from castings, the size and metric are ours, and the babbitt alloy has no head yet.

مواد

8

ابزارهای لازم

4

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...