همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Canoe Sailing Rig: Bamboo Mast, 9 ft Lateen Sail, Clamp-In Mast Thwart and Leeboards (Boy Mechanic, 1919)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۹
۰
۰
۰
۰

Canoe Sailing Rig: Bamboo Mast, 9 ft Lateen Sail, Clamp-In Mast Thwart and Leeboards (Boy Mechanic, 1919)

Stillman Taylor's sailing outfit for a 16 ft open canoe from The Boy Mechanic, Book 3 (1919): a 6 ft 10 in bamboo mast, a 9 ft lateen sail of cotton sheeting on two bamboo spars, a mast thwart and leeboard thwart that clamp to the gunwales with brass lantern-board hooks, and leeboards set by thumb nuts. Steer with the paddle.
متوسط
A few days

دستورالعمل‌ها

1

Rig sizes and sail area

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic, Book 3

"The lateen rig is best for an open canoe, because a shorter mast is required for the same sail area ... It is not safe to rig a canoe too heavily, and the rig described has been found to be well proportioned."
3

Make the mast

Cut bamboo 1-1/2 in across to 6 ft 10 in (carpet dealers' rolling bamboo of 1-1/2 to 2 in serves). Whittle a tapered wooden plug about 3 in long to wedge firmly in the top without splitting the cane, bore a small hole through the cane 2 in from the top, and fix a screw eye into the plug for the halyard. Drive small brads through the cane into the plug, and fit a brass ferrule over the end.

مواد مورد نیاز این مرحله:

تیرک‌های بامبوتیرک‌های بامبو1 قطعه
تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
پیچ حلقه‌ایپیچ حلقه‌ای1 قطعه
میخمیخ1 قطعه
حلقهٔ فلزیحلقهٔ فلزی1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
کارد چرم‌بریکارد چرم‌بری
دریل دستیدریل دستی
چکشچکش
4

Make the spars

Use two bamboo fishing rods, 1 in at the butt and 10 ft long, as gaff and boom. Fix a 1-1/2 in screw eye with a 1/2 in eye at the end of each and join the spar ends with a 1-1/2 in brass split ring and a 1-3/4 in brass S hook. Fasten the 2 in brass boom jaw on the boom with its open end 18 in from the boom's forward end.

مواد مورد نیاز این مرحله:

میلهٔ بامبومیلهٔ بامبو2 قطعه
پیچ حلقه‌ایپیچ حلقه‌ای2 قطعه
حلقهٔ جاکلیدی دولاحلقهٔ جاکلیدی دولا1 قطعه
قلاب S شکلقلاب S شکل1 قطعه
فک بومفک بوم1 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

دریل دستیدریل دستی
پیچ‌گوشتی تختپیچ‌گوشتی تخت
متر نواریمتر نواری
5

Sew the sail

Lay the spars on the cloth and pencil a triangle 9 ft on each side. Sew the widths of 1 yd unbleached cotton sheeting together, lapped about 1/2 in and stitched close to both edges, preferably on a machine. Sew bights (folds) 1/2 in wide, 6 in apart, parallel with the leech. Reinforce the corners with segments of cloth. Along the edges lashed to the spars fold and sew 1 in hems, running a 1/2 in tape into the leech hem; fasten the tape to the spar at each end to take up stretch and stop a flapping leech.

مواد مورد نیاز این مرحله:

پارچهٔ پنبه‌ایپارچهٔ پنبه‌ای8 yard
نخ خیاطینخ خیاطی1 قطعه
نوار سرژه پنبه‌اینوار سرژه پنبه‌ای1 قطعه

ابزارهای مورد نیاز:

چرخ خیاطیچرخ خیاطی
قیچیقیچی
مدادمداد
متر نواریمتر نواری
6

Make the thwarts and mast step

Mast thwart: two cedar or pine boards 28 by 10 by 3/8 in and a piece 27-1/2 by 3-1/2 by 3/4 in, made as in the plate with a hole in the centre for the mast and a brass lantern-board hook at each end to clamp it to the gunwales. Mast step: a block 5 by 2-1/2 by 1 in, shaped neatly, fixed to the grating (or the ribs). Leeboard thwart: cedar or white pine 5 ft by 4 by 7/8 in, with short upright ends set at an angle to the canoe's curve so it wedges in just aft of the mast; groove the ends to the thwart and screw them on. He gives no leeboard sizes; bolt a leeboard to each end with a 3 in by 5/16 in brass bolt, washer and thumb nut so its angle can be set.

مواد مورد نیاز این مرحله:

تختهٔ سرو قرمزتختهٔ سرو قرمز4 قطعه
قلاب تختهٔ فانوسقلاب تختهٔ فانوس4 قطعه
پیچ‌ومهرهٔ بخاریپیچ‌ومهرهٔ بخاری2 قطعه
واشر تختواشر تخت2 قطعه
مهره بالدارمهره بالدار2 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
ارهٔ موییارهٔ مویی
رندهٔ دستیرندهٔ دستی
اسکنه‌هااسکنه‌ها
دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
پیچ‌گوشتی تختپیچ‌گوشتی تخت
7

Finish and rig

Smooth all woodwork with sharp tools, sandpaper lightly, and give three coats of spar varnish. Lash the sail to the spars, run the 1/4 in cotton-rope halyard through the screw eye at the masthead until the gaff is close to the top, and find the balance by tying the halyard at different points along the gaff. Run the halyard under the forward thwart to the stern, never tied to it, and loop the main sheet round a thwart and hold it, never made fast.

مواد مورد نیاز این مرحله:

کاغذ سنبادهکاغذ سنباده1 قطعه
ورنی دکلورنی دکل1 قطعه
طناب پنبه‌ایطناب پنبه‌ای1 قطعه

ابزارهای مورد نیاز:

قلم‌موی پهنقلم‌موی پهن
قیچیقیچی
8

Sailing safely

Canoe sailing.

Flow

Loading...
9

History and honest limits

From "How to Build a Canoe, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 86-88). He gives no leeboard sizes (they vary with the canoe); the list calls the leeboard bolts brass stove bolts with thumb nuts and the text carriage bolts with wing nuts. Cedar for the leeboards, the sail area and the metric figures are ours.

مواد

21

ابزارهای لازم

14
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...