هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

ایجاد شده توسط

Woody

6. اکتبر 2026NO
۱۰
۰
۰
۰
۰

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
متوسط
About 4 hours

دستورالعمل‌ها

1

Sheet speed from the slot

در حال بارگذاری دفترچهٔ Jupyter…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

مواد مورد نیاز این مرحله:

برس سایشبرس سایش1 قطعه

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
ارهٔ موییارهٔ مویی
ماژیک ثابتماژیک ثابت
خط‌کشخط‌کش
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

ابزارهای مورد نیاز:

مجموعه اسکنهٔ چوبمجموعه اسکنهٔ چوب
چکشچکش
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
چاقوی کاردستیچاقوی کاردستی
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

مواد مورد نیاز این مرحله:

لولهٔ مسیلولهٔ مسی1 قطعه
اتصالات برنجیاتصالات برنجی1 قطعه

ابزارهای مورد نیاز:

لوله‌برلوله‌بر
سوهان (سوهان دستی)سوهان (سوهان دستی)
آچار فرانسهآچار فرانسه
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

مواد مورد نیاز این مرحله:

چسب درزگیر سیلیکونچسب درزگیر سیلیکون1 قطعه
ورق لاستیکورق لاستیک1 قطعه
ورق آلومینیومورق آلومینیوم1 قطعه
پیچ چوب #8 در ۱ اینچپیچ چوب #8 در ۱ اینچ1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
چاقوی کاردستیچاقوی کاردستی
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

مواد مورد نیاز این مرحله:

لولهٔ مسیلولهٔ مسی1 قطعه
شیر توپیشیر توپی1 قطعه
اتصالات برنجیاتصالات برنجی1 قطعه
نوار آب‌بندی رزوه از PTFEنوار آب‌بندی رزوه از PTFE1 قطعه
قوطی حلبیقوطی حلبی1 قطعه
چسب درزگیر سیلیکونچسب درزگیر سیلیکون1 قطعه

ابزارهای مورد نیاز:

لوله‌برلوله‌بر
آچار فرانسهآچار فرانسه
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
مرحله 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
مرحله 10 - Image 1

مواد مورد نیاز این مرحله:

شلنگ باغبانیشلنگ باغبانی1 قطعه
آبآب1 قطعه

ابزارهای مورد نیاز:

پارچ اندازه‌گیریپارچ اندازه‌گیری
کرونومترکرونومتر
خط‌کشخط‌کش
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

مواد

12

ابزارهای لازم

17

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...