همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۷
۰
۰
۰
۰

Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)

Homer E. Willard and Frederick S. Young of Toledo, Ohio, received US 2,146,458, dated 7 February 1939, for a simple portable router with few moving parts. The motor sits in an open-fronted support in the middle of a T-shaped frame, so the bit and the work are always in view. The frame stands on three legs on the table beside the clamped work: two curved legs at one end, and at the other a screw with a knob. Turning the knob with one hand raises or lowers the bit while it cuts. We print the frame in PETG round a small DC motor. The sizes are ours.
متوسط
About 1 day

دستورالعمل‌ها

1

Depth by the knob

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 2,146,458

"Thus, by turning the wrist in one direction or the other, the bit 19 may be raised or lowered, as required, without stopping the motor and without removing the hands from the tool."
3

Print the frame

The T-shaped frame 10: the motor support 13 with its ledge 14 (an 18 mm hole and two M4 holes 29 mm apart) and curved wall 15, open at the front 16; arm 11 to the cross with two curved legs 21, 22; arm 12 to a boss with an M10 nut trap for the screw leg 24. PETG, 0.2 mm layers, 40 % infill, 5 walls; print it legs up, ledge on the bed.
فایل طراحیSTLCC0 - Free
4

Fit the motor

Print the frame. Fit the collet adapter on the motor's shaft, stand the motor in the support with its face on the ledge and the collet through the hole, and screw it down with two M4 screws. Wire it through a toggle switch to the DC supply as for our 1924 router.

مواد مورد نیاز این مرحله:

فیلامنت PETGفیلامنت PETG1 قطعه
موتور برقیموتور برقی1 قطعه
آداپتور کولت شفت موتورآداپتور کولت شفت موتور1 قطعه
پیچ آلن سرتخت‌استوانه‌ایپیچ آلن سرتخت‌استوانه‌ای2 قطعه
کلید اهرمیکلید اهرمی1 قطعه
سیم اتصالسیم اتصال1 قطعه
لولهٔ حرارتی جمع‌شوندهلولهٔ حرارتی جمع‌شونده1 قطعه

ابزارهای مورد نیاز:

چاپگر سه‌بعدی رشته‌ای (FDM)چاپگر سه‌بعدی رشته‌ای (FDM)
منبع تغذیهٔ جریان مستقیممنبع تغذیهٔ جریان مستقیم
هویه برقیهویه برقی
مجموعه آچار آلنمجموعه آچار آلن
5

The screw leg and knob

Press an M10 nut into the trap under the boss. Cut 100 mm of M10 threaded rod, round its lower end with a file so it slides on the table, and screw it up through the nut. Turn a hardwood knob 25, bore it, and glue it on the rod's top with a nut locked under it.

مواد مورد نیاز این مرحله:

مهرهٔ شش‌گوشمهرهٔ شش‌گوش2 قطعه
میلهٔ رزوه‌شدهمیلهٔ رزوه‌شده1 قطعه
تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
چسب چوبچسب چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
مجموعه سوهانمجموعه سوهان
تراش چوبتراش چوب
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
آچار فرانسهآچار فرانسه
6

Rout

Clamp the work down on the table between two strips. Fit a bit and stand the router on the table so its legs are beside the work and the bit is over it. Turn the knob until the bit just clears the work, switch on, and turn it down a little while moving the router over the area to be cut, one hand on arm 11 and the other on the knob.

ابزارهای مورد نیاز:

مجموعهٔ تیغه‌های اورفرزمجموعهٔ تیغه‌های اورفرز
تختهٔ چوب سختتختهٔ چوب سخت
گیرهٔ میله‌ایگیرهٔ میله‌ای
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
عینک ایمنیعینک ایمنی
7

Troubleshooting

Three-legged router troubleshooting.

Flow

Loading...
8

History and honest limits

**Homer E. Willard** and **Frederick S. Young** of Toledo, Ohio, US 2,146,458, dated 7 February 1939, filed 11 December 1935. They claimed "a portable router comprising a T-shaped frame having a semi-circular recess in the stem of the T, a bit-operating motor mounted in said recess and a leg projecting in the same direction as the bit from each of the ends of the frame", one leg "screw-threaded through the arm and terminating above the arm in an operating knob". Their work was an electrotype clamped on the table; their motor ran on mains. Ours is a small DC motor in a printed frame. They give no sizes; every size here is ours.

مواد

11

ابزارهای لازم

15

فایل‌های طراحی

1

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...