LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Air Blow Gun: Press-Button Valve and Conical Air Shield
Harry Yates's air gun (US 2,604,361, 1952) for blowing chips off lathes and drills. A press-button valve is held shut by the line pressure itself; pressed, it lets air into a ribbed nozzle that splits it into a central jet and a cone of air from a ring slot, which keeps flying chips away from the worker's eyes. The rubber valve face comes out by unscrewing one cap.
The patent gives no materials (except the rubber face), threads or sizes; the machine tools named are ours. The picture: the patent's drawing.
Lengra kominn
1 day
Leiðbeiningar
1
1
Bore the body
Bore the body
Bore the body's vertical opening: stem bearing (13), wider air passage (14), wider chamber (15) threaded at the bottom (16), with a valve seat rib (17) undercut round its edge. Ours: lathe and boring bar, tap for the thread.
Efni fyrir þetta skref:
Hús blástursbyssu1 stykkiNauðsynleg verkfæri:
Málmrennibekkur
Borstöng
Snittsett2
2
Bore the hose pocket so it breaks into the chamber
Bore the hose pocket so it breaks into the chamber
Bore and thread the hose pocket (19) so its edge cuts into the chamber, opening the port (20) and leaving a centre projection (21): an overhang that turns incoming air down into the chamber, away from the seat.
Nauðsynleg verkfæri:
MálmrennibekkurBorstöngSnittsett3
3
Bore the barrel
Bore the barrel
Bore the front barrel (11) to a cylindrical pocket (22) joined to the air passage by a tapered passage (23). Bevel the barrel's front end (44).
Nauðsynleg verkfæri:
MálmrennibekkurBorstöng4
4
Fit stem and press-button
Fit stem and press-button
Pass the valve stem (24) up through the body and press its stud (25) into the socket (27) of the press-button (28). The button slides in the bearing; the stem's flange (26) stops it coming out upward, the button head downward. Ours: arbor press.
Efni fyrir þetta skref:
Ventilstöng1 stykki
Þrýstihnappur ventils1 stykkiNauðsynleg verkfæri:
Handpressa5
5
Make the valve closure
Make the valve closure
Set the rubber valve face (36) in the recess (35) on top of the closure member (30) and press a flanged tubular eyelet (37) into its centre hole (38) to hold it.
Efni fyrir þetta skref:
Lokunarhluti ventils1 stykki
Gúmmíþéttiflötur ventils1 stykki
Hólknagli1 stykkiNauðsynleg verkfæri:
Handpressa6
6
Close the chamber
Close the chamber
Slide the closure's stud (31) into the pocket (32) of the closure cap (33) and screw the cap into the chamber, a gasket (34) under its flange. The stem's pin (29) rests on the closure. Ours: flat screwdriver in the cap's slot.
Efni fyrir þetta skref:
Lokunartappi1 stykki
Pakkning1 stykkiNauðsynleg verkfæri:
Flatskrúfjárn7
7
Press in the nozzle
Press in the nozzle
Force the nozzle's ribs (41) into the barrel pocket (22) until its inner end stops on the tapered passage (23). That stop fixes the ring slot (45) between the nozzle's cone shoulder (42) and the barrel bevel (44).
Efni fyrir þetta skref:
Loftstútur1 stykkiNauðsynleg verkfæri:
Handpressa8
8
Screw on the tip and the hose nipple
Screw on the tip and the hose nipple
Screw the tip (49) into the nozzle's threaded pocket (48); its bore (50) is wider than the jet hole (47) so it does not touch the jet, and it can clamp an extension tube. Screw a hose nipple into the hose pocket (19).
Efni fyrir þetta skref:
Stútoddur1 stykki
Snittaður slöngunippill1 stykkiNauðsynleg verkfæri:
Skiptilykill9
9
Try the jet and the shield
Try the jet and the shield
Ours: connect an air hose from a compressor. The line pressure alone holds the valve shut. Press the button: a central jet leaves the jet hole, and a cone of air from the ring slot surrounds it.
Nauðsynleg verkfæri:
Loftþjappa
LoftslangaEfni
11- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.