LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Building a Carbon Monoxide Detector
Ed

Búin til af

Ed

13. júlí 2026FI
76
0
0
0
0

Building a Carbon Monoxide Detector

Build a circuit that senses carbon monoxide (CO) — the invisible, odourless gas from any incomplete combustion — and raises an alarm when it rises. An MQ-7 sensor gives the Arduino a reading that climbs with CO; the code compares it to a clean-air baseline and triggers a buzzer and red LED. A great way to learn gas sensing — but read the safety note: this is a demonstration, NOT a certified life-safety CO alarm.

Miðlungs
1-2 hours

Leiðbeiningar

1

Wire the sensor, buzzer and LED

On the breadboard: MQ-7 VCC to Arduino 5V, GND to GND, and its analog output (AOUT) to Arduino A0. Active buzzer + to pin 8, - to GND. Red LED anode to pin 7 through a 330 Ω resistor, cathode to GND.

Efni fyrir þetta skref:

Arduino Uno R3Arduino Uno R31 stykki
Carbon Monoxide Sensor - MQ-7Carbon Monoxide Sensor - MQ-71 stykki
Virkur suðeiningVirkur suðeining1 stykki
5 mm LED5 mm LED1 stykki
330 ohm viðnám330 ohm viðnám1 stykki
TengibrettiTengibretti1 stykki
TengivírarTengivírar1 pakki
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port.

Nauðsynleg verkfæri:

Tölva með Arduino IDETölva með Arduino IDE
USB-B-snúraUSB-B-snúra
3

Upload the detector sketch

Paste this sketch and upload. It warms the sensor for two minutes, records a clean-air baseline, then sounds the buzzer and lights the LED whenever the reading climbs above that baseline.

co_detector.inoarduino
// Carbon monoxide INDICATOR using an MQ-7 sensor.
// NOT a certified life-safety alarm - see the blueprint's safety note.
// MQ-7 analog output on A0; buzzer on pin 8; red warning LED on pin 7.

const int MQ7_PIN = A0;
const int BUZZER_PIN = 8;
const int LED_PIN = 7;

int cleanAirValue = 0;          // baseline, measured at startup
const int ALARM_MARGIN = 150;   // how far above baseline triggers the alarm

void setup() {
  pinMode(BUZZER_PIN, OUTPUT);
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);

  Serial.println("Warming up the MQ-7 (2 min) in clean air...");
  delay(120000);                // 2-minute warm-up
  cleanAirValue = analogRead(MQ7_PIN);
  Serial.print("Clean-air baseline: ");
  Serial.println(cleanAirValue);
}

void loop() {
  int reading = analogRead(MQ7_PIN);
  Serial.println(reading);

  if (reading > cleanAirValue + ALARM_MARGIN) {
    digitalWrite(LED_PIN, HIGH);      // CO above baseline -> alarm
    digitalWrite(BUZZER_PIN, HIGH);
  } else {
    digitalWrite(LED_PIN, LOW);
    digitalWrite(BUZZER_PIN, LOW);
  }
  delay(500);
}
4

Warm up, baseline and test

Power it in fresh air and let the 2-minute warm-up set the clean-air baseline (a brand-new MQ-7 also needs a longer 24–48 h burn-in before its readings settle). Then hold a small CO source nearby in a ventilated room — the smoke from a just-blown-out match works — and the buzzer and LED should trigger. Change ALARM_MARGIN to make it more or less sensitive.

5

Important safety limits

This is a LEARNING project and, at best, a supplementary indicator — it is NOT a certified life-safety device. A hobby MQ-7 gives a relative reading, not a calibrated ppm; it drifts over time and needs regular re-baselining, and it also responds to smoke and other gases. Carbon monoxide is invisible, odourless and can be fatal: for real protection always use a UL- or EN-certified CO alarm. Never rely on this circuit to keep anyone safe.

Efni

7

Nauðsynleg verkfæri

3
Áætlað alls
Það sem smiðurinn keypti. Efni án verðs færðu þar sem þú kaupir það.
$7.11

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

Building an Ultrasonic Parking Sensor

Building an Ultrasonic Parking Sensor

eftir EdFI

Stafrænt

51
0
0
0
0
0
Blinking LED — Your First Arduino Project
BLUEPRINT NFT

Blinking LED — Your First Arduino Project

eftir Admiral OOMNO

Stafrænt

576
2
1
7
0
0

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...