LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Claw Hammer: Drop-Forged Head, Turned Wooden Handle
A claw hammer's head is high-carbon steel, hot forged between dies and then hardened only where it takes the blows: the face, the poll and the claws. The handle is straight-grained ash or hickory, woods with good strength, durability and enough give to absorb the shock of repeated blows. It is turned on a lathe that copies a cam, pushed up through the head's eye and wedged: one thin wooden wedge driven diagonally into a slot, then two steel wedges driven through it crossways.
Lengra kominn
Factory process
Leiðbeiningar
1
1
Heat the bar
Heat the bar
Heat a length of steel bar to about 1,200–1,300 °C (2,200–2,350 °F) with open flame torches or by passing it through an induction coil.
Efni fyrir þetta skref:
Ferstrent verkfærastál1 as requiredNauðsynleg verkfæri:
Spanhitari2
2
Forge the head
Forge the head
Put the hot bar or a cut blank between the dies. The ram forces them together and squeezes the steel into the die cavities; repeat in several dies to form the head step by step.
Nauðsynleg verkfæri:
Fallhamar með smíðamótum3
3
Trim the flash
Trim the flash
Cut off the flash, the steel squeezed out between the dies, with trimming dies. Cool the head and grind off rough spots.
Nauðsynleg verkfæri:
Afgratunarmót
Bekkslípivél4
4
Harden the face, poll and claws
Harden the face, poll and claws
Heat those areas with a flame or an induction coil and cool them quickly, so the steel near the surface becomes much harder than the rest of the head.
Nauðsynleg verkfæri:
Spanhitari5
5
Clean and polish
Clean and polish
Shot blast the head (a stream of air carrying small steel particles), paint it if wanted, then polish the face, poll, claws and cheeks. Smooth the V-slot of the claws with an abrasive disc.
Nauðsynleg verkfæri:
Skotblástursskápur
Fægiskífa6
6
Turn the handle
Turn the handle
Cut ash or hickory to length and hold it at both ends in the lathe. As it spins, the cutting tool follows a cam with the handle's shape. Cut a slot diagonally across the top and sand the handle smooth.
Efni fyrir þetta skref:
Harðviðarefni í sköft1 stykkiNauðsynleg verkfæri:
Kambstýrður skaftrennibekkur
Sandpappír7
7
Hang the head
Hang the head
Push the handle up through the eye of the head. Tap the wooden wedge into the diagonal slot to spread the handle against the head, then drive two small steel wedges through it crossways.
Efni fyrir þetta skref:
Harðviðarkíll1 stykki
Þverfleygar úr stáli2 stykkiEfni
4- 1 as requiredStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2 stykkiStaðgengill
Nauðsynleg verkfæri
8- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.