LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Diagonal Screw Dasher Churn: Dished Blades on a Slanting Shaft Twist the Butter Together
Jacob Boyers of Granville, Virginia, received US 13,421, dated 14 August 1855, for dished, perforated dashers set "at an angle thereto, so as to resemble a screw" on a shaft laid diagonally in the tub, so the butter is gathered "lump joining lump as it is twisted by the screw."
This rung prints the dashers, step and top slot, fits them in a tub and makes butter.
Miðlungs
About 3 hours, plus printing
Leiðbeiningar
1
1
The diagonal shaft
The diagonal shaft
Hleð Jupyter-vinnubók…
2
2
A screw in the churn before it
A screw in the churn before it
An upright screw keeps the cream moving; Boyers lays his screw diagonally.
3
3
Read US 13,421
Read US 13,421
"The placing the shaft diagonally in the tub, is not from mere caprice; its position enables me to create a vortex, or whirlpool; the lower end of the shaft, viz., at A; while on the opposite side of the tub, viz., at B, the butter is comparatively quiet and suffered to gather in lumps."
4
4
Print the parts
Print the parts
Print three dashers, with supports under the dished blades, the corner step and the top slot. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Efni fyrir þetta skref:
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari5
5
Print the dasher
6
6
Print the corner step
Print the corner step
The corner step, printed as step 4 describes.
7
7
Print the top slot
8
8
Tub and shaft
Tub and shaft
Use a rectangular food-grade container about 260 by 180 mm and 220 mm deep. Seal the step into one bottom corner with food-safe silicone and clip the top slot on the opposite rim. Slide the dashers onto a 10 mm square hardwood shaft, each turned 60° from the last, and lay it from the step into the slot. Glue a crank arm and handle on its top end.
Efni fyrir þetta skref:
Geymslubox í matvælaflokki1 stykki
Sílikonþéttiefni1 stykki
Harðviðartappar1 stykki
Furuborð1 stykki
Trélím1 stykkiNauðsynleg verkfæri:
Handsög
Hleðslubor
Borasett9
9
The build in 3D
The build in 3D
FreeCAD model of this build: the tub cut away to show the diagonal shaft from the corner step to the top slot, with three pairs of dished, perforated blades set like a screw.
10
10
Churn
Churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Turn the crank steadily and watch the butter gather on the quiet side; time until it comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Efni fyrir þetta skref:
Rjómi2000 ml
Gróft sjávarsalt1 stykki
Vatn1 stykkiNauðsynleg verkfæri:
Hitamælir með nema sem situr í
Skeiðklukka
Stafræn eldhúsvog
Stór hrærskál úr ryðfríu stáli11
11
Troubleshooting
Troubleshooting
Diagonal screw dasher troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Jacob Boyers** of Granville, Virginia (the specification writes "Monongahela" County), US 13,421, 14 August 1855. He claimed the shaft combined with the dashers as arranged. A container and printed parts stand in for his tub. FDM prints hold food in their layer lines, so wash well and replace when worn.
Efni
9- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2000 mlStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
8- Staðgengill
- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
4Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
Screw-Lift Churn: An Archimedean Screw Keeps the Whole Body of Cream Moving
eftir Emma
MATUR OG DRYKKUR
24
0
0
0
0
0
Air-Chest Spiral Agitator Churn: A Disk That Draws Air Down Its Agitator Into the Cream
eftir Emma
MATUR OG DRYKKUR
35
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
eftir TheChef
HANDVERK
54
0
0
0
0
0
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.