Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)
Penny

Búin til af

Penny

2. nóvember 2026DK
6
0
0
0
0

Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)

The equal-arm balance with its weights replaced by electricity. The pan sits on a coil in the gap of a permanent magnet. A load pushes it down; capacitor rings sense the smallest movement, and a servo drives just enough current through the coil to lift it back to its rest position. That current is the weight. Result: a balance that reads the weight in grams or ounces on a digital display, with no weights to handle, and tare by its circuit. Source: C. B. Akers and others (Arbor Laboratories), US Patent 4,034,819 (1977). Unknown: the resolution, capacity, magnet type, materials and sizes; the circuits are given as blocks only. Picture: patent drawing.
Lengra kominn
2 weeks

Leiðbeiningar

1

Build the magnet circuit

Stack permanent magnets into a column with a soft iron core. Enclose them in an annular outer housing with end caps, shaped so the field crosses a narrow annular air gap at a constriction. Keep the whole structure symmetrical about its vertical axis. Mount it on a support plate fixed to an upright, such as a housing panel on a base. Not given: the magnet type, materials and sizes.

Efni fyrir þetta skref:

Lítill segullLítill segull1 column
JárnteinnJárnteinn1 soft iron core
Óþekktur málmurÓþekktur málmur1 housing and end caps
Óþekktur efniviðurÓþekktur efniviður1 support plate, panel, base

Nauðsynleg verkfæri:

SkrúfjárnasettSkrúfjárnasett
Óþekkt málÓþekkt mál
2

Hang the coil in the gap

Wind the coil tightly round the middle of a light bobbin that surrounds the core, the coil sitting in the air gap. Tabs at both ends of the bobbin pass out through holes in the end caps to suspension frames. Hang the frames from thin springy cantilevers fixed to the upright, so the bobbin can only move a short way straight up and down. Keep the bobbin and its suspension as light as possible. Put the weighing pan on top. Ours: enamelled wire.

Efni fyrir þetta skref:

Lakkeinangraður koparvírLakkeinangraður koparvír1 coil
Óþekktur efniviðurÓþekktur efniviður1 bobbin, frames, cantilevers
VogarskálVogarskál1 stykki

Nauðsynleg verkfæri:

Óþekkt málÓþekkt mál
3

Fit the capacitor rings

Mount four capacitor rings inside the outer housing, two above and two below the air gap, facing matching rings on the bobbin. Cross-connect them so a tilt of the bobbin cancels out and only up-and-down movement shows. Connect them to a signal generator: as the bobbin moves, one set's capacitance rises and the other's falls, and the difference becomes the control voltage.

Efni fyrir þetta skref:

Óþekktur málmurÓþekktur málmur1 rings
SamrásSamrás1 sensing circuit
TengivírTengivír1 stykki
LóðtinsvírLóðtinsvír1 a little

Nauðsynleg verkfæri:

LóðboltiLóðbolti
4

Close the servo loop and read the current

Feed the control voltage to a d.c. servo that drives current through the coil, through a flexible lead, until the bobbin is back at its rest position. Pass that current through a large stable resistor, a thermal resistor that corrects for temperature and a calibration potentiometer: the voltage across them stands for the weight. A separate circuit (comparators, saw-tooth generator, oscillator and counter) turns it into a count read out as grams or ounces. Tare is ordinary circuit logic. Ours: a segment LCD; check with calibration weights.

Efni fyrir þetta skref:

SamrásSamrás1 servo and counting circuits
ViðnámViðnám2 stable resistor, thermal resistor
RennistilliviðnámRennistilliviðnám1 calibration
LCD-skjár með hlutumLCD-skjár með hlutum1 display
LóðtinsvírLóðtinsvír1 a little

Nauðsynleg verkfæri:

LóðboltiLóðbolti
KvörðunarlóðasettKvörðunarlóðasett

Efni

12

Nauðsynleg verkfæri

4

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...