Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Sliding-Strip Cylinder Dash Churn: Strips on the Slats Open the Gaps One Way and Close Them the Other
Daniel K. France of Congress, Ohio, received US 25,404, dated 13 September 1859, for a cylindrical churn-dash. Two crosses of curved arms carry four groups of three slats, each slat half by one inch. On each group a metal strip with a slot down its middle is held by screws in short slots, so it slides when the dash changes direction and opens or closes the spaces between the slats. Turned one way the dash churns; reversed, it gathers the butter into a corner. Two cog wheels at three to one drive it.
France gives one size, the slats; every other size here is ours.
Miðlungs
About 2 days, plus printing
Leiðbeiningar
1
1
France's slats, and the wheels' three to one
France's slats, and the wheels' three to one
Hleð Jupyter-vinnubók…
2
2
A turning dasher on crossed arms in a box, before it
A turning dasher on crossed arms in a box, before it
That dasher's boards were fixed. France's slats carry strips that open and close the gaps with the turning.
3
3
Read US 25,404
Read US 25,404
"The motion of the dash to be to the left in the direction of the curve of the arms while churning, thereby producing the greatest amount of friction in the cream. When butter is produced the motion of the dash is reversed and the butter gathered in the lower left corner of the churn by the reversed action thereon of the dash and self adjusting slide."
4
4
Print the large cog wheel
Print the large cog wheel
The 48-tooth spur wheel (module 3) with a hub, bored 20.4 mm, for the crank's stud. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the small cog wheel
Print the small cog wheel
The 16-tooth spur pinion (module 3) with a hub, bored 20.4 mm, for the dash's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Box with legs and lid
Box with legs and lid
From 20 mm hardwood cut a bottom 440 x 340 mm, two sides 440 x 300 mm, two ends 300 x 300 mm and a lid 440 x 340 mm. Bore each end 20.8 mm through its middle, 150 mm above the floor, for the shaft. Glue and screw the ends between the sides and the box onto the bottom, and screw four legs of 70 mm timber, 350 mm long, under it. Fill the box with water overnight so it swells tight, then empty it.
Efni fyrir þetta skref:
Harðviðarborð3 stykki
Mjúkviður 70x70 mm1 stykki
Trélím1 stykki
Tréskrúfur30 stykkiNauðsynleg verkfæri:
Borðsög
Handsög
Hleðslubor
Spaðabora-sett
Stangarþvinga
Fastur vinkill
Málband
Vatn7
7
Dash: arms, hubs and slats
Dash: arms, hubs and slats
Cut eight curved arms from 22 mm hardwood with the jigsaw, each 18 mm wide, sweeping 30 degrees from a 20 mm hub radius out to 112 mm. Glue four into a 56 mm hardwood hub to make a cross, twice, all curving the same way, and bore the hubs 20.4 mm. Cut twelve slats 12.7 x 25.4 mm, 340 mm long, and screw them to the arms' ends in groups of three, 9 mm apart, flat side out, so their faces are 125 mm from the middle.
Efni fyrir þetta skref:
Harðviðarborð1 stykkiTrélím1 stykkiTréskrúfur24 stykkiNauðsynleg verkfæri:
StingsögBorðsögHleðsluborSpaðabora-sett
BorasettMálband8
8
Strips B with slots C and screws D
Strips B with slots C and screws D
Cut four strips of 0.8 mm stainless sheet, 324 mm long and as wide as a group of slats (94 mm). Cut a slot C 9 mm wide along the middle of each, stopping 30 mm from the ends, and a short slot across each end. Lay each strip on its group's outer face and fix it with an M4 screw through each end slot into the arm's end, just loose enough to slide sideways. Turned one way, the cream pushes each strip so its slot lies over the slats; the other way, over a space.
Efni fyrir þetta skref:
Plata úr ryðfríu stáli1 stykki
Vélskrúfur8 stykki
Flöt skinna8 stykkiNauðsynleg verkfæri:
Plötuklippur
Þjalir (handþjöl)HleðsluborBorasett
Skrúfjárnasett9
9
Shaft, cog wheels and crank
Shaft, cog wheels and crank
Pass a 20 mm stainless shaft through one end of the box, the two hubs and the other end, and pin the hubs to it. On the outside of the geared end, screw a hardwood block 96 mm above the shaft, fix a 20 mm stud in it, and fit the large wheel on the stud with a crank and handle. Pin the small wheel on the shaft's end meshing with it.
Efni fyrir þetta skref:
Stöng úr ryðfríu stáli2 stykkiHarðviðarborð1 stykki
Harðviðartappar1 stykki
Sexkantboltaúrval3 stykki
Læsiró með nælonhring3 stykki
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari
JárnsögHleðsluborBorasett
Skiptilykill10
10
The build in 3D
The build in 3D
FreeCAD model of this build, front side cut away: the dash's two crosses of curved arms, the four groups of slats with their strips, slots and screws, the shaft through the box's ends, and the two cog wheels and crank outside. The dash was turned through 16 angles.
11
11
Churn, then gather
Churn, then gather
Pour about 6 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Turn the crank so the dash turns with the curve of its arms, timing it. When the butter comes, turn the crank the other way so the strips slide over and the dash gathers the butter into a corner. Lift it out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Efni fyrir þetta skref:
Rjómi6 l
Gróft sjávarsalt1 stykkiVatn1 stykkiNauðsynleg verkfæri:
Hitamælir með nema sem situr í
Skeiðklukka
Stafræn eldhúsvog
Stór hrærskál úr ryðfríu stáli12
12
Troubleshooting
Troubleshooting
Sliding-strip churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Daniel K. France** of Congress, Wayne County, Ohio, US 25,404, 13 September 1859, "Churn-Dash". He claimed the metallic strips B on the convex surface of the slats, held by slots and screws. He disclaimed slats or beaters hinged to the arms. His slats, half by one inch, are kept; every other size is ours. His plates A, changed to reverse the dash when the crank is used alone, are not built.
Efni
15- 3 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2 stykkiStaðgengill
- 54 stykkiStaðgengill
- 1 stykkiStaðgengill
- 8 stykkiStaðgengill
- 8 stykkiStaðgengill
- 2 stykkiStaðgengill
- 1 stykkiStaðgengill
- 3 stykkiStaðgengill
- 3 stykkiStaðgengill
- 1 stykkiStaðgengill
- 6 lStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
20- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
3Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
Rotary-Dasher Box Churn: Float Boards on Crossed Arms in a Curved Box
eftir Martin
MATUR OG DRYKKUR
47
0
0
0
0
0
Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up
eftir Buttercup
Trésmiði
2
0
0
0
0
0
Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter
eftir Buttercup
Trésmiði
2
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
eftir TheChef
HANDVERK
60
0
0
0
0
0
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.