LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
GRÆN FRAMTÍÐ
ÖFUGVERKFRÆÐI
SKÓLAVERKEFNI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Blowing a Glass Bottle by Hand — Free-Blown Vessel Shaping
Forge

Búin til af

Forge

26. maí 2026NO
27
0
0
3
0

Blowing a Glass Bottle by Hand — Free-Blown Vessel Shaping

Free-blowing a glass bottle is one of the foundational skills in glassworking. The glassblower gathers molten soda-lime glass on a blowpipe, inflates it into a bubble, and shapes the body, neck, and lip using a combination of gravity, centrifugal force, and simple hand tools. Unlike mould-blown glass, free-blown bottles are shaped entirely by the maker's skill — every piece is unique. This technique has been used continuously since Roman times and remains the basis of all studio glassblowing today.

Miðlungs
2-3 hours (plus annealing overnight)

Leiðbeiningar

1

Heat the furnace and prepare the bench

Bring the glass furnace to working temperature (~1100°C) with a crucible of molten soda-lime glass. Set up the glassblower's bench — a seat with two parallel rails for rolling the blowpipe. Have all tools within arm's reach.

Nauðsynleg verkfæri:

Brick FurnaceBrick Furnace
2

Mix and charge the glass batch

If starting from raw batch: combine approximately 60% silica sand, 25% soda ash, and 15% crushed limestone. Charge into the crucible and melt over 4-6 hours until clear and bubble-free.

Efni fyrir þetta skref:

Quartz SandQuartz Sand2 kg
Sodium Carbonate (soda ash)Sodium Carbonate (soda ash)800 g
Calcium Carbonate (limestone, crushed)Calcium Carbonate (limestone, crushed)500 g

Nauðsynleg verkfæri:

Clay Crucible (refractory)Clay Crucible (refractory)
3

Pre-heat and gather on the blowpipe

Pre-heat the blowpipe tip in the furnace mouth for 30 seconds. Dip into the molten glass and rotate slowly to collect a symmetrical gather about the size of a tennis ball. Withdraw smoothly.

Nauðsynleg verkfæri:

Glassblowing BlowpipeGlassblowing Blowpipe
4

Marver the gather

Roll the gather back and forth on a flat marver (granite slab or steel plate) to centre the glass on the pipe and create a uniform cylindrical shape. Keep the pipe rotating constantly to prevent the glass from drooping.

Nauðsynleg verkfæri:

Granite SlabGranite Slab
5

Blow the initial bubble

Seal the end of the blowpipe with your thumb, then give a short firm puff to inflate a small bubble inside the gather. This first bubble (the 'parison') is the foundation of the bottle shape. Roll on the marver again to even out the walls.
6

Reheat and expand the bubble

Return the parison to the furnace mouth (glory hole) for 10-15 seconds until it glows evenly. Blow again to enlarge the bubble to the desired bottle size. Control the shape by holding the pipe at different angles — gravity pulls the soft glass downward, elongating it.
7

Shape the body with the jacks

While rotating the pipe, use glassmaker's jacks (large spring-loaded tweezers with flat blades) to constrict the glass and form the neck. Squeeze gently below where the neck meets the body to create a defined shoulder. Between tool passes, cup and smooth the hot glass with a folded wet block — a cupped piece of cherry wood kept soaking wet, or several layers of folded newspaper drenched in water. The steam cushion lets you shape the glass by hand pressure without burning. Keep rotating to maintain symmetry.

Nauðsynleg verkfæri:

Glassmaker's JacksGlassmaker's Jacks
Folded Wet Block (cherry wood or soaked newspaper)Folded Wet Block (cherry wood or soaked newspaper)
8

Form the base

Hold the pipe vertically with the bottle hanging down. Tap the pipe or use a wooden paddle to flatten the base slightly so the bottle will stand upright. A traditional wine bottle has a concave 'push-up' base — press a wetted wooden tool into the still-soft base to create this indent.
9

Attach the pontil rod

Gather a small bit of hot glass on a pontil rod and press it firmly against the centre of the bottle base. Allow it to fuse. The pontil will hold the bottle while the lip is formed.

Nauðsynleg verkfæri:

Pontil RodPontil Rod
10

Crack off the blowpipe

Score the glass at the blowpipe junction with a wet file or apply a drop of water. Tap the pipe to crack off cleanly. The bottle is now held by the pontil rod with the neck opening upward.
11

Form the lip and finish the neck

Reheat the rough neck opening at the furnace mouth. Use the jacks to flare or shape the lip — a rounded lip for pouring, or a flanged collar for accepting a stopper. The lip must be smooth and even.

Nauðsynleg verkfæri:

Long-Handled Fire TongsLong-Handled Fire Tongs
12

Crack off the pontil

Apply a wet iron to the pontil junction and tap to separate. This leaves a rough scar (the pontil mark) on the bottle base — the traditional sign of a hand-blown bottle.
13

Transfer to the annealing oven

Immediately place the finished bottle into a pre-heated annealing oven at approximately 500°C. The bottle must cool slowly — rapid cooling creates internal stresses that cause cracking.
14

Anneal overnight

Reduce the oven temperature gradually at 20-30°C per hour through the critical range (500-350°C). Below 350°C the cooling rate can increase. A typical bottle anneals fully in 8-12 hours. Do not open the oven until the temperature matches room temperature.
15

Grind the pontil scar smooth

Once fully cooled, grind the rough pontil scar on the base using a wet sandstone or silicon carbide wheel. The base should be flat enough for the bottle to stand without rocking. Inspect the entire bottle for cracks or thin spots.

Efni

3

Nauðsynleg verkfæri

8

Efni úr tengdum teikningum

Required Equipment

Equipment this kind of build typically needs — buy from any maker below.

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Recommended for this build

Products makers often use with builds like this one.

CharcoalFrequently used with this build's materials
Grozing PliersUsed in similar builds
Diamond ScriberUsed in similar builds
Crucible Tongs (long-handled)Frequently used with this build's materials
Leather Gauntlet GlovesFrequently used with this build's materials
Safety GogglesFrequently used with this build's materials
Charcoal Furnace (small)Frequently used with this build's materials
Glass MullerFrequently used with this build's materials

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

Making Window Glass by the Crown Glass Method — Spinning Molten Glass into Flat Paneseftir Forge
Making Soda Ash by the Leblanc Process — The Chemical That Made Soap and Glass Affordableeftir Charlie

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Making a Glass Bead on a Mandrel — Lampwork BeadmakingGlassworking
Making Window Glass by the Crown Glass Method — Spinning Molten Glass into Flat PanesGlassworking
Binding a Besom Broom — The Birch-Twig Broom on a Hazel Handle
Regrowing Vegetables from Their Bases — Free Greens from Kitchen Scraps
Alloying Bronze (Cu + Sn) — The Bronze Age Beginsmaterials/metals
Building a Voltaic Pile — The First Battery and the Birth of Steady ElectricityELECTRONICS

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...