LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Half-Round Can Opener: Push the Cutter In and Twist
Opening a sardine box or tin with a flat knife takes many strokes and leaves a ragged edge.
Seth P. Chapin of Atlantic, New Jersey, received US 56,368, dated 17 July 1866, for an implement for opening sheet-metal cans and boxes: a cutter semicircular in section with sloping edges to a point, bevelled inside, on a handle; forced in nearly to the handle and twisted, it cuts a circle the size of its own curve, and a guard at its top keeps it in position and stops it going too deep.
This rung works out how many twists a hole takes, then files the cutter from steel tube and opens a can.
Byrjandi
About 2 hours
Leiðbeiningar
1
1
Twists for a full circle
Twists for a full circle
Hleð Jupyter-vinnubók…
2
2
A cutter turned round before it
A cutter turned round before it
The embedded blueprint shears tin round a wheel. Chapin bends the blade into a half-tube so twisting it cuts a circle.
3
3
Read US 56,368
Read US 56,368
"The said edges a are beveled upon their inner side to make them sufficiently sharp, and the implement is used for cutting circular holes in the tin box by forcing it, point first, into and through the sheet metal nearly up to the end of the handle A, and then turning or twisting the cutter around by means of the said handle, which causes the foremost of the edges a to cut the thin metal in a circular line corresponding to the circle of which the back or convex side of the cutter forms an arc."
4
4
Cut the half tube
Cut the half tube
Cut 45 mm of 25 mm steel tube and saw it in half lengthwise. Keep one half.
Efni fyrir þetta skref:
Stálrör1 stykkiNauðsynleg verkfæri:
Járnsög
Skrúfstykki
Merkipenni
Reglustika5
5
Shape the point
Shape the point
File both long edges to slope in to a point at one end, over the last 25 mm. Bevel them inside with a round needle file and hone.
Nauðsynleg verkfæri:
Þjalir (handþjöl)
Nálaþjalasett
BrýniSkrúfstykki
Tær öryggisgleraugu6
6
Guard and handle
Guard and handle
Epoxy a large flat washer across the cutter's top as the guard, and a hardwood handle above it.
Efni fyrir þetta skref:
Flöt skinna1 stykki
Harðviðartappar1 stykki
Tveggja þátta epoxý1 stykkiNauðsynleg verkfæri:
Sandpappír7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: a 25 mm half-tube cutter with sloping edges to a point, the washer guard and the hardwood handle.
8
8
Twist out a hole
Twist out a hole
Stand a sealed can on the kitchen scale. Force the point through the top until the guard meets it, then twist round; count the twists, read the peak load and measure the hole.
Efni fyrir þetta skref:
Blikkdós1 stykkiNauðsynleg verkfæri:
Stafræn eldhúsvog
Stafrænn skífmælir 6 tommur
Skeiðklukka
Vinnuhanskar úr leðri9
9
A cutter that will not enter, wanders or jams
A cutter that will not enter, wanders or jams
Half-round can opener troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Seth P. Chapin** of Atlantic, Monmouth County, New Jersey, received US 56,368, dated 17 July 1866, for opening tin or other sheet-metal boxes in circles or straight or irregular lines. Widened at its widest part, the cutter cuts a larger part of a circle or oval at one thrust, leaving a piece easily bent over; another form has one edge flattened for sardine boxes, and a metal handle with a cross-piece for turning. Wyman's 1868 patent names it.
**Honest limits.** A washer stands in for his guard, and the tube is unhardened. Your twist counts are the result.
Efni
5- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
13- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
1Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.