LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Propeller-and-Spoon Egg Beater: Spoon Arms Break the Swirl
A turning beater soon sets the whole liquid circling with it.
William T. Nicholson of Providence, Rhode Island, received US 32,886, dated 23 July 1861, for an egg beater: a crank wheel with bevelled face teeth turns a pinion and a pair of propeller blades; under the pinion a disk with an elliptic groove rocks two arms ending "in the form of a spoon bill's beak," so "the circling currents occasioned by the blades of the propeller will be broken at regular intervals." It clamps into a socket on a table or lifts out for use by hand.
This rung works out the stroke rates, then prints the crown wheel, pinion, cam and propeller, builds the frame and arms, and times a beating.
Lengra kominn
About 5 hours, plus printing
Leiðbeiningar
1
1
Stroke rates
Stroke rates
Hleð Jupyter-vinnubók…
2
2
A crank wheel and pinion before it
A crank wheel and pinion before it
The embedded blueprint drives two beaters off one wheel. Nicholson drives a propeller and lets a cam rock two spoon arms against its swirl.
3
3
Read US 32,886
Read US 32,886
"To the under side of the pinion E is secured the disk H (Fig. 5,) its lower surface being furnished with an elliptic groove or channel I. Two arms K K pivoted to the handle at c and d extend to the bottom of the propeller blade their lower extremities being in the form of a spoon bill's beak. A projecting ear e, e on each arm is inserted in the elliptic groove I whereby as the propeller shaft F is rotated to which the disk is attached a reciprocating motion is given to each of the arms."
4
4
Print the gears, cam and propeller
Print the gears, cam and propeller
Print the 48-tooth crown wheel, the 12-tooth pinion, the cam disk with its elliptic groove and the propeller. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Efni fyrir þetta skref:
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari5
5
Print the crown wheel
Print the crown wheel
The crown wheel, printed as step 4 describes.
6
6
Print the pinion
7
7
Print the cam
8
8
Print the propeller
9
9
Frame and wheel
Frame and wheel
Cut a plywood handle frame. Bolt the crown wheel to it on an M5 screw with a crank near its rim, and drill a bearing for the propeller shaft so the pinion meshes the wheel's face.
Efni fyrir þetta skref:
Krossviðarplata1 stykki
Vélskrúfur1 stykki
Flöt skinna1 stykki
Sexkantró1 stykkiNauðsynleg verkfæri:
Laufsög
Hleðslubor
Borasett
Skiptilykill10
10
Shaft, cam and propeller
Shaft, cam and propeller
Epoxy the pinion, then the cam under it, on a 5 mm rod through the bearing, and the propeller on the rod's foot.
Efni fyrir þetta skref:
Kringlótt stöng úr deigu stáli1 stykki
Tveggja þátta epoxý1 stykkiNauðsynleg verkfæri:
Járnsög
Skrúfstykki11
11
Spoon arms
Spoon arms
Bend two arms of stainless wire with a spoon-shaped flat at the foot. Pivot each on a screw in the frame either side of the shaft, and bend a short ear on each into the cam's groove.
Efni fyrir þetta skref:
Vír úr ryðfríu stáli1 stykki
Tréskrúfa #8 x 1"1 stykkiNauðsynleg verkfæri:
Kringlunefjatöng
Flatkjaftatöng
Skrúfjárnasett
Stafrænn skífmælir 6 tommur12
12
The patent drawing
The patent drawing
US 32,886 drawing sheet, public domain (expired patent).
13
13
With and without the arms
With and without the arms
Beat two egg whites with the arms in the groove and time them to stiff peaks; lift the ears out and repeat with the propeller alone.
Efni fyrir þetta skref:
Egg4 stykkiNauðsynleg verkfæri:
Stór hrærskál úr ryðfríu stáli
Skeiðklukka14
14
Arms that jam, a cam that throws them
Arms that jam, a cam that throws them
Propeller-and-spoon egg beater troubleshooting.
Flow
Loading...
15
15
History and honest limits
History and honest limits
**William T. Nicholson** of Providence, Rhode Island, received US 32,886, dated 23 July 1861. The grooved disk is set with its longest diameter in the same plane as the propeller blades, so the arms clear the blades; the socket or chair fixes to a table by spurs and one wood screw, its inclined sides grasping the handle, which can be lifted out for use by hand. He claimed the reciprocating beaters combined with a revolving beater.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinion stand in for his bevelled wheel, and a plywood frame for his handle and socket. Your times are the result.
Efni
10- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 4 stykkiStaðgengill
Nauðsynleg verkfæri
13- Staðgengill
- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
4Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.