LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Screw-Tube Egg Beater: The Tube Spins, the Rod Stands Still
A push-spinning egg beater turns on its point in the bowl: it wanders, and pressing on it slows it.
Walter Hart of Philadelphia received US 31,663, dated 12 March 1861, for an egg beater whose wire beaters are on a tube with a screw thread, spun by a nut slid up and down; inside it a rod fixed to the handle ends in a button that rests on the bottom of the vessel, so "the base ... is stationary and therefore has no tendency to slip" and the pressure is borne by the rod, leaving the tube free to turn.
This rung works out the tube's turns per stroke, then prints the lobed screw tube and nut, fits rod, button and beaters, and times a beating.
Byrjandi
About 2 hours, plus printing
Leiðbeiningar
1
1
Turns per stroke
Turns per stroke
Hleð Jupyter-vinnubók…
2
2
A spiral and slide before it
A spiral and slide before it
The embedded blueprint turns two scrolls with a slide on two spirals. Hart turns one screw tube and stands the whole beater on a still rod.
3
3
Read US 31,663
Read US 31,663
"In my improved egg beater the base, consisting of the button e, which rests on the bottom of the vessel, is stationary and therefore has no tendency to slip and as the pressure imparted to it is sustained by the stationary rod and not by the tube the latter is free to rotate under any pressure to which the instrument may be necessarily subjected."
4
4
Print the tube and nut
Print the tube and nut
Print the three-lobed screw tube standing upright, and the nut. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Efni fyrir þetta skref:
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari5
5
Print the tube
6
6
Print the nut
7
7
Bend the beaters
Bend the beaters
Bend three loops of stainless wire about 32 mm across and 45 mm high, and epoxy their ends round the tube's lower end.
Efni fyrir þetta skref:
Vír úr ryðfríu stáli1 stykki
Tveggja þátta epoxý1 stykkiNauðsynleg verkfæri:
Kringlunefjatöng
Flatkjaftatöng8
8
Rod, button and handle
Rod, button and handle
Pass a 5 mm rod through the tube, with the nut on the tube. Epoxy a washer to the rod's foot as the button, leaving the tube 2 mm of play, and a hardwood handle on its top.
Efni fyrir þetta skref:
Kringlótt stöng úr deigu stáli1 stykki
Flöt skinna1 stykki
Harðviðartappar1 stykkiTveggja þátta epoxý1 stykkiNauðsynleg verkfæri:
Járnsög
Skrúfstykki
Hleðslubor
Borasett9
9
The patent drawing
The patent drawing
US 31,663 drawing sheet, public domain (expired patent).
10
10
Beat egg whites
Beat egg whites
Stand the button on the bowl's bottom, hold the handle, and slide the nut up and down; time two whites to stiff peaks. Note whether the button stays put.
Efni fyrir þetta skref:
Egg2 stykkiNauðsynleg verkfæri:
Stór hrærskál úr ryðfríu stáli
Skeiðklukka11
11
A tube that sticks, a nut that binds
A tube that sticks, a nut that binds
Screw-tube egg beater troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Walter Hart** of Philadelphia received US 31,663, dated 12 March 1861. His thread is three wires coiled on the tube, their lower ends spread into the beaters; the nut is wood with a pin entering between the wires; a strip of metal lapped spirally may replace the wires. He did not claim the screw spindle, beaters and nut as such, which were known, but their combination with the internal rod and button.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A printed lobed tube stands in for his wire thread. Your times are the result.
Efni
7- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2 stykkiStaðgengill
Nauðsynleg verkfæri
9- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
2Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
Spiral-Slide Egg Beater: Push a Slide, Two Scrolls Turn Opposite Ways
eftir Emma
MATUR OG DRYKKUR
37
0
0
0
0
0
Ratchet-Bar Egg Beater: Push a Rack, the Floats Spin Both Ways
eftir YourGrandma
MATUR OG DRYKKUR
41
0
0
0
0
0
Oblique-Rack Egg Beater: One Rack Turns Two Beaters Opposite Ways
eftir Emma
MATUR OG DRYKKUR
38
0
0
0
0
0
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.