LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Forge

Búin til af

Forge

18. október 2026NO
16
0
0
0
0

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered

Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours. The picture: steel sewing needles (Wikimedia Commons).
Miðlungs
Half a day

Leiðbeiningar

1

Cut, soften and straighten

Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.

Efni fyrir þetta skref:

PíanóvírPíanóvír70 mm

Nauðsynleg verkfæri:

HliðarbíturHliðarbítur
SmiðjueldstæðiSmiðjueldstæði
NefjatöngNefjatöng
SteðjiSteðji
2

Point

Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.

Nauðsynleg verkfæri:

ÞjalasettÞjalasett
SkrúfstykkiSkrúfstykki
ÖryggisglerauguÖryggisgleraugu
3

Flatten and pierce the eye

Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.

Nauðsynleg verkfæri:

SteðjiSteðji
ÞverfleygshamarÞverfleygshamar
HandborHandbor
ÞjalasettÞjalasett
SkrúfstykkiSkrúfstykki
ÖryggisglerauguÖryggisgleraugu
4

Harden in oil

Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.

Nauðsynleg verkfæri:

SmiðjueldstæðiSmiðjueldstæði
NefjatöngNefjatöng
Herðsluker með olíuHerðsluker með olíu
ÖryggisglerauguÖryggisgleraugu
5

Temper

Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.

Nauðsynleg verkfæri:

HitameðferðarofnHitameðferðarofn
Hitanemapar með aflestriHitanemapar með aflestri
SteðjiSteðji
ÞverfleygshamarÞverfleygshamar
6

Scour and polish

Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.

Nauðsynleg verkfæri:

SmergildúkurSmergildúkur
ÓlífuolíaÓlífuolía
SápaSápa
SagSag
LeðurstrokkariLeðurstrokkari
ÞjalasettÞjalasett

Efni

1

Nauðsynleg verkfæri

17

Þessi teikning býr til

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...