ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
FUTURO VERDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Blinking an LED with LilyPad Arduino
Ed

Creato da

Ed

13. luglio 2026FI
5
0
0
0
0

Blinking an LED with LilyPad Arduino

Step up from a plain sewn circuit to a sewable computer. The LilyPad Arduino is a washable microcontroller you program from your PC, then run on a coin cell — so your fabric can blink, fade and react on its own. This project sews an LED to the board and uploads the classic 'blink' sketch: the gateway to every sensor-driven wearable that follows.

Intermedio
1 hour

Istruzioni

1

Sew the LilyPad Arduino and an LED

Sew a LilyPad Arduino Simple board and a LilyPad LED onto felt with conductive thread: the LED's + tab to numbered pin 5, and the LED's - tab to the board's - tab. Loop 3–4 times through each hole, trim tails, and keep the two lines from crossing.

Materiali per questo passaggio:

LilyPad Arduino Simple BoardLilyPad Arduino Simple Board1 pezzo
LilyPad LED - 5 pcsLilyPad LED - 5 pcs1 confezione
Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 rocchetto
Hand Sewing Needles (Assorted, 30-Pack)Hand Sewing Needles (Assorted, 30-Pack)1 confezione
Wool Felt SheetWool Felt Sheet1 foglio
2

Connect the FTDI programmer

Plug a LilyPad FTDI Basic Breakout onto the board's 6-pin programming header (line up GND to GND, DTR to DTR) and connect it to your computer with a USB cable. Install the free Arduino IDE, then choose the LilyPad Arduino board and the FTDI's serial port under Tools.

Materiali per questo passaggio:

LilyPad FTDI Basic Breakout - 5VLilyPad FTDI Basic Breakout - 5V1 pezzo
SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 pezzo

Strumenti necessari:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the blink sketch

Paste this sketch into the Arduino IDE and click Upload. It flashes the LED on pin 5 on and off twice a second.

lilypad_blink.inoarduino
// Blink an LED sewn to a LilyPad Arduino
// The LED's + tab is stitched to pin 5, its - tab to the board's - (GND).

const int LED_PIN = 5;   // LilyPad LED sewn to pin 5

void setup() {
  pinMode(LED_PIN, OUTPUT);   // pin 5 drives the LED
}

void loop() {
  digitalWrite(LED_PIN, HIGH); // LED on
  delay(500);                  // wait half a second
  digitalWrite(LED_PIN, LOW);  // LED off
  delay(500);                  // wait half a second
}

// TRY THIS:
// - delay(100) for fast blinking, delay(2000) for slow
// - different ON and OFF times: HIGH delay(800), LOW delay(200)
4

Go wireless on a coin cell

Unplug the FTDI. Sew a LilyPad coin-cell battery holder to the board — + tab to +, - tab to - — and drop in a CR2032. Switch it on and the LED blinks on its own, no computer attached. Your fabric now runs its own program.

Materiali per questo passaggio:

LilyPad Coin Cell Battery Holder - w/Switch - 20mmLilyPad Coin Cell Battery Holder - w/Switch - 20mm1 pezzo
CR2032 Coin Cell BatteryCR2032 Coin Cell Battery1 pezzo
5

Experiment

Re-attach the FTDI and change the sketch: adjust the delays for a heartbeat rhythm, or sew a second LED to another pin and blink them in turn. This is the base every LilyPad sensor project builds on.

Materiali

9

Strumenti richiesti

1
Totale stimato
€78.00

Blueprint correlati

Questi blueprint condividono conoscenze — tecniche, materiali o principi

Sewing a LilyPad LED Circuitdi Ed
Blinking LED — Your First Arduino Projectdi Admiral OOM

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Using an LCD — SIK Circuit 15electronics
Sewing a LilyPad LED Circuitelectronics
Making a LilyPad Night-Lightelectronics
Making a Motion-Reactive LilyPad Patchelectronics
Making a Sound-Triggered LilyPad Patchelectronics
Making a Color-Changing LilyPad Patchelectronics

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...