ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
Martin

Creato da

Martin

6. ottobre 2026NO
34
0
0
0
0

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

A single whisk carries the egg round with it rather than cutting through it. James F. Monroe of Fitchburg, Massachusetts, and E. P. Monroe of New York received US 23,694, dated 19 April 1859, for an egg beater: a frame clamped to a table carries a bevel wheel turned by a handle, gearing into two pinions on opposite sides of it; one turns an inner beater of bent wires, the other an outer beater round it, "in opposite directions." This rung works out the beater speeds, then prints the crown wheel and pinions, bends the beaters, and times a beating.
Intermedio
About 5 hours, plus printing

Istruzioni

1

Beater speeds

Caricamento del notebook Jupyter…
2

The gear train it uses

The embedded blueprint works gear ratios and direction. Monroe takes two pinions off opposite sides of one wheel so they turn opposite ways.
3

Read US 23,694

"This invention consists in arranging in an adjustable frame two beaters, one inside the other, which receive motion in opposite directions by means of two pinions which gear into a large bevel wheel and on opposite sides of the same, so that by rotating the bevel wheel by means of a handle the beaters receive the required motion."
4

Print the gears

Print the 48-tooth crown wheel (/uploads/blueprints/counter-rotating-egg-beater-crown-wheel.stl) and two 12-tooth pinions (/uploads/blueprints/counter-rotating-egg-beater-pinion.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Materiali per questo passaggio:

Filamento PETGFilamento PETG1 pezzo

Strumenti necessari:

Stampante 3D a filamento (FDM)Stampante 3D a filamento (FDM)
5

Build the frame

Cut a plywood upright and two arms. Bolt the crown wheel to the upright on an M5 screw with washers so it turns freely, and fix a handle screw near its rim. Drill the arms 5 mm on the line through both pinions' centres.

Materiali per questo passaggio:

Pannello di compensatoPannello di compensato1 pezzo
Viti da metalloViti da metallo1 pezzo
Rondella pianaRondella piana1 pezzo
Dado esagonaleDado esagonale1 pezzo
Vite da legno #8 x 1"Vite da legno #8 x 1"1 pezzo

Strumenti necessari:

Sega da traforoSega da traforo
Trapano a batteriaTrapano a batteria
Serie di punte da trapanoSerie di punte da trapano
Chiave regolabile a rullinoChiave regolabile a rullino
Set di cacciavitiSet di cacciaviti
6

Arbor and inner beater

Cut 200 mm of 5 mm rod. Epoxy one pinion on it to mesh at the wheel's top, and bend two wire loops 28 mm across at its lower end.

Materiali per questo passaggio:

Tondo di acciaio dolceTondo di acciaio dolce1 pezzo
Filo di acciaio inoxFilo di acciaio inox1 pezzo
Resina epossidica bicomponenteResina epossidica bicomponente1 pezzo

Strumenti necessari:

Seghetto per metalliSeghetto per metalli
Pinze a becchi tondiPinze a becchi tondi
Pinze a becchi piattiPinze a becchi piatti
7

Sleeve and outer beater

Glue the second pinion to a length of silicone tube sleeved loosely over the rod, meshing at the wheel's bottom. Bend two wire loops 48 mm across and fix them to the sleeve's lower end, round the inner beater.

Materiali per questo passaggio:

Tubo in siliconeTubo in silicone1 pezzo
Filo di acciaio inoxFilo di acciaio inox1 pezzo
Resina epossidica bicomponenteResina epossidica bicomponente1 pezzo

Strumenti necessari:

Pinze a becchi tondiPinze a becchi tondi
Pinze a becchi piattiPinze a becchi piatti
Calibro digitale da 6 polliciCalibro digitale da 6 pollici
8

The patent drawing

US 23,694 drawing sheet, public domain (expired patent).
Passo 8 - Image 1
9

Beat egg whites

Clamp the frame to the table over the bowl with two egg whites. Turn the handle about once a second and time how long until they hold stiff peaks.
Passo 9 - Image 1

Materiali per questo passaggio:

UovoUovo2 pezzi

Strumenti necessari:

Grande ciotola da impasto in acciaio inossidabileGrande ciotola da impasto in acciaio inossidabile
CronometroCronometro
10

Beaters that turn together, jam or clash

Counter-rotating egg beater troubleshooting.

Flow

Loading...
11

History and honest limits

**James F. Monroe** of Fitchburg, Massachusetts, and **E. P. Monroe** of New York, assignors to E. P. Monroe, received US 23,694, dated 19 April 1859, reissued 16 October 1860 (No. 1,062). The frame's fork clamps to a table with a set screw and washer. The second pinion lies loose on the arbor, driving the outer beater whose lower collar turns loosely round the arbor's end. They noted it also mixes paint. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinions stand in for his bevel gears, and a silicone sleeve for his loose pinion. Your times are the result.

Materiali

11

Strumenti richiesti

12

Questo progetto realizza

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...