Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)
A variable DC supply regulated by controlled rectifiers instead of a series transistor. Two of the four rectifiers in the bridge are silicon controlled rectifiers; how late in each half-cycle they are fired sets the output. A voltage bridge and a current bridge each make an error signal, an analog OR gate passes whichever is larger, and the supply crosses over automatically between holding the voltage and holding the current.
Result: a variable voltage / current regulated DC supply with automatic cross-over.
Source: K. Kupferberg and J. Ash (Forbro Design), US 3,305,763 (1967), Fig. 1. Unknown: component values and the firing-angle circuit. Picture: the patent drawing.
Avanzato
Unknown
Istruzioni
1
1
Build the controlled rectifier bridge
Build the controlled rectifier bridge
In a case, wire the cord through a switch and fuse to a transformer. Feed its secondary into a bridge of two ordinary rectifiers and two silicon controlled rectifiers. Smooth the negative output through a choke and a capacitor, then through a current-sensing resistor (with a second capacitor forming a further filter) to the negative output terminal; the positive goes straight to the positive terminal. Ours: the case, switch and fuse. Not given: the ratings.
Materiali per questo passaggio:
Contenitore in alluminio1 pezzo
Cavo flessibile con spina1 pezzo
Interruttore a levetta1 pezzo
Fusibile1 pezzo
Trasformatore riduttore1 pezzo
Diodo2 pezzi
Tiristore (SCR)2 pezzi
Induttanza di filtro1 pezzo
Condensatore elettrolitico2 pezzi
Boccola da pannello2 output + and -Strumenti necessari:
Trapano a mano
Set di cacciaviti2
2
Build the two bridges
Build the two bridges
Current bridge: the sensing resistor, a reference Zener, a fixed resistor and the variable current-control resistor. Voltage bridge: the load across the output, the variable voltage-control resistor, a fixed resistor and a second reference Zener. Feed both Zeners from a small separate supply. Not given: the values, the Zener supply.
Materiali per questo passaggio:
Diodo Zener2 pezzi
Reostato2 voltage and current controls
Resistenza1 sensing and bridge resistorsStrumenti necessari:
Saldatore a stagno3
3
Build the control chain and use it
Build the control chain and use it
Invert the current bridge's error in a phase-reversing amplifier and feed it, with the voltage bridge's error, to an analog OR gate that passes the larger. Amplify the result and feed it to a firing-angle control circuit that fires the two controlled rectifiers' gates later or earlier in each half-cycle. In use, set the voltage and the current: for any load larger than the cross-over resistance (voltage setting divided by current setting) the supply holds the voltage, for a smaller one the current. Not given: the amplifier, OR-gate and firing circuits in this form.
Materiali per questo passaggio:
Circuito stampato1 pezzo
Assortimento di transistor1 amplifiers
Materiale sconosciuto1 OR gate and firing-angle circuit
Filo per saldatura1 as neededStrumenti necessari:
Saldatore a stagnoMateriali
17- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- Segnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 2 pezziSegnaposto
- 2 pezziSegnaposto
- 1 pezzoSegnaposto
- 2 pezziSegnaposto
- Segnaposto
- 2 pezziSegnaposto
- 2 voltage and current controlsSegnaposto
- 1 sensing and bridge resistorsSegnaposto
- 1 pezzoSegnaposto
- 1 amplifiersSegnaposto
- 1 OR gate and firing-angle circuitSegnaposto
- 1 as neededSegnaposto
Strumenti richiesti
3- Segnaposto
- Segnaposto
- 2 vendors sell this, none ship to you yetSegnaposto
Questo progetto realizza
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.