Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher
Alfred Guthrie of Chicago received US 24,907, dated 26 July 1859, for a churn with no dasher at all. Four upright shafts in a frame have cranks on their tops, and a bed plate lies over the four crank pins, so each crank turns on its own centre but all move together. The tub stands on the plate, held by stirrups, and is carried round a small circle, throwing the cream against its sides. A handle turns one crank shaft through cogged gearing.
This rung builds it at the patent's own sizes: a frame about two feet square and one foot high, shafts of 3/4 inch iron and 3 inch cranks.
Intermedio
About 2 days, plus printing
Istruzioni
1
1
How hard the cream is swung
How hard the cream is swung
Caricamento del notebook Jupyter…
2
2
A churn with a dasher, before it
A churn with a dasher, before it
Wineman's dasher drove the cream through holes. Guthrie did away with the dasher and moved the whole tub.
3
3
Read US 24,907
Read US 24,907
"I connect the whole together by the bed plate D over the wrists of each crank E, E, E, E. Each crank will revolve upon its own center but will each correspond to the motion of the other."
4
4
Print the wheel H
Print the wheel H
The 64-tooth spur wheel (module 3, 198 mm across) for the handle shaft I, with a 20 mm bore. PETG, 0.2 mm layers, 50 % infill, 5 walls.
5
5
Print the pinion H
Print the pinion H
The 24-tooth spur pinion for the driven crank shaft, with a 19 mm bore and a hub. PETG, 0.2 mm layers, 50 % infill, 5 walls.
6
6
Frame and bearing bars
Frame and bearing bars
Build a pine frame 610 mm square and 305 mm high: four 50 mm corner posts, and 50 mm rails round the top and the bottom. Fit two hardwood bars across it, top and bottom, 150 mm in front of and behind the middle, and bore them 19.6 mm square to the frame at 200 mm either side of the middle, for the four shafts. Screw two hardwood brackets to the right side, top and bottom, bored 20.6 mm 132 mm out from the front right shaft, for the handle shaft.
Materiali per questo passaggio:
Tavola di pino2 pezzi
Legno tenero 70x70 mm2 pezzi
Tavola di legno duro2 pezzi
Vite da legno n. 10 x 3"24 pezzi
Colla da legno1 pezzoStrumenti necessari:
Sega a mano
Trapano a batteria
Set di punte a lancia
Squadra fissa
Livella a bolla
Metro a nastro7
7
Shafts, cranks and plate D
Shafts, cranks and plate D
Cut four 19 mm steel shafts 323 mm long and stand them in the bars. Make four hardwood crank arms, 76 mm from the shaft to the crank pin, and pin them on the shafts' tops all pointing the same way. Fit a 19 mm steel crank pin 50 mm long in each. Cut plate D 532 mm across from plywood, bore it for the four pins exactly where they stand, and drop it on them. Turn one crank by hand: the plate must run round freely without turning.
Materiali per questo passaggio:
Barra di acciaio grezza2 pezziTavola di legno duro1 pezzo
Pannello di compensato1 pezzo
Rondella piana8 pezzi
Assortimento di bulloni a testa esagonale4 pezzi
Dado autobloccante con inserto in nylon4 pezziColla da legno1 pezzoStrumenti necessari:
Seghetto per metalli
Lime (lima a mano)
Morsa da bancoTrapano a batteria
Serie di punte da trapano
Seghetto alternativoMetro a nastro
Chiave regolabile a rullino8
8
Gearing H and handle I
Gearing H and handle I
Pin the pinion on the front right shaft 140 mm up. Stand a 20 mm steel shaft 885 mm long in the brackets, pin the wheel on it level with the pinion, and check they mesh fully. Fix a hardwood handle arm 150 mm long on the shaft's top with a dowel grip.
Materiali per questo passaggio:
Filamento PETG1 pezzoBarra di acciaio grezza1 pezzoTavola di legno duro1 pezzo
Tasselli di legno duro1 pezzoColla da legno1 pezzoStrumenti necessari:
Stampante 3D a filamento (FDM)Seghetto per metalliTrapano a batteriaSerie di punte da trapano9
9
Tub F on its grooved bottom
Tub F on its grooved bottom
Glue a plywood ring to the plate's middle, 282 mm inside and 340 mm outside, so the bucket's foot sits in it. Bend two flat-bar stirrups to go up the bucket's sides and over its lid, notch the ring for them and bolt them to the plate.
Materiali per questo passaggio:
Pannello di compensato1 pezzoColla da legno1 pezzo
Piatto di acciaio dolce2 pezziAssortimento di bulloni a testa esagonale4 pezziDado autobloccante con inserto in nylon4 pezzi
Secchio da 20 litri1 pezzoStrumenti necessari:
Seghetto alternativoMorsa da bancoSeghetto per metalliTrapano a batteriaSerie di punte da trapanoChiave regolabile a rullino10
10
The build in 3D
The build in 3D
FreeCAD model of this build: the frame with its bearing bars, the four shafts and cranks, plate D on the crank pins, the bucket in its ring under two stirrups, and the spur wheel on the handle shaft driving the pinion. It was checked at eight crank angles.
11
11
Churn
Churn
Pour about 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, put the lid on and tighten the stirrups. Turn the handle steadily and time it. When the butter comes, lift the bucket off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Materiali per questo passaggio:
Panna da montare8 l
Sale marino grosso1 pezzo
Acqua1 pezzoStrumenti necessari:
Termometro a sonda permanente
Cronometro
Bilancia digitale da cucina
Grande ciotola da impasto in acciaio inossidabile12
12
Troubleshooting
Troubleshooting
Four-crank churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Alfred Guthrie** of Chicago, Illinois, assignor to Wardell Guthrie, US 24,907, 26 July 1859, "Churn". He claimed the cranks C connected by the plate D. His sizes are kept: a frame about two feet square and one foot high, shafts of 3/4 inch iron about a foot long, and cranks of 3 inches, which we read from "about a six inch throw or three inches" and Fig. 3's "3 in" marks. He gives no gear sizes; ours are printed spur gears placed as his Figs. 2-3 draw them. Every other size is ours.
Materiali
17- 2 pezziSegnaposto
- 2 pezziSegnaposto
- 2 pezziSegnaposto
- 24 pezziSegnaposto
- 4 pezziSegnaposto
- 2 pezziSegnaposto
- 1 pezzoSegnaposto
- 8 pezziSegnaposto
- Segnaposto
- Segnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 2 pezziSegnaposto
- 1 pezzoSegnaposto
- Segnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
Strumenti richiesti
17- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
File di progetto
3Questo progetto realizza
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.