ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI

Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall
A. C. Stiles of South Bloomfield, Ohio, received US 3,764, dated 27 September 1844, for a rocking churn: an oblong box on rockers, split by a partition with holes, with a dasher on each side worked by arms on shafts across the ends, and one upright lever that rocks the box and works the dashers together.
This rung prints the partition, dashers and arms, builds the box and makes butter.
Avanzato
About 6 hours, plus printing
Istruzioni
1
1
One lever, three motions
One lever, three motions
Caricamento del notebook Jupyter…
2
2
Two dashers from one lever, before it
Two dashers from one lever, before it
Mitchell worked two dashers from one lever; Stiles adds rockers and a perforated partition between them.
3
3
Read US 3,764
Read US 3,764
"The machine is operated by moving the upright lever l, to and fro, which rocks the box, while at the same time it works the dashers up and down, thus throwing the cream through the partition d, till the butter is made."
4
4
Print the parts
Print the parts
Print the partition (/uploads/blueprints/rocking-twin-dasher-lever-churn-partition.stl), two dashers (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher.stl), two dasher arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher-arm.stl) and two lower arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-lower-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materiali per questo passaggio:
Filamento PETG1 pezzoStrumenti necessari:
Stampante 3D a filamento (FDM)5
5
Box on rockers
Box on rockers
Build a pine box about 260 × 120 × 150 mm with a close-fitting lid, sealed inside. Glue the partition across its middle and screw two curved pine rockers lengthwise underneath. Drill the lid for the two dasher handles.
Materiali per questo passaggio:
Tavola di pino1 pezzo
Colla da legno1 pezzo
Vite da legno #8 x 1"1 pezzoStrumenti necessari:
Sega a mano
Sega da traforo
Trapano a batteria
Serie di punte da trapano
Morsetti6
6
Shafts, arms and lever
Shafts, arms and lever
Set a 10 mm square shaft across each end on two studs, 60 mm above the lid. Fit a dasher arm on each, pointing inward and pinned to its dasher's handle, and a lower arm on each outside the box. Join the lower arms with a pine bar, and pivot an upright pine lever on a block near the box's foot, pinned to the bar's middle.
Materiali per questo passaggio:
Tasselli di legno duro1 pezzo
Tavola di pino1 pezzo
Tondo di acciaio dolce1 pezzo
Viti da metallo1 pezzoStrumenti necessari:
Sega a mano
Trapano a batteria
Serie di punte da trapano
Set di cacciaviti7
7
The patent drawing
The patent drawing
US 3,764 drawing sheet, public domain (expired patent).

8
8
Rock and churn
Rock and churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Work the lever to and fro: the box rocks and the dashers rise and fall in turn. Keep fingers clear of the arms and the rockers. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materiali per questo passaggio:
Panna da montare1500 ml
Sale marino grosso1 pezzo
Acqua1 pezzoStrumenti necessari:
Termometro a sonda permanente
Cronometro
Bilancia digitale da cucina
Grande ciotola da impasto in acciaio inossidabile9
9
Troubleshooting
Troubleshooting
Rocking twin-dasher churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**A. C. Stiles** of South Bloomfield, Pickaway County, Ohio, US 3,764, 27 September 1844. He claimed the combination of the rockers and dashers in the double-chambered churn. His drawing gives no sizes; ours are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.
Materiali
11- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1500 mlSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
Strumenti richiesti
11- Segnaposto
- Segnaposto
- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
Questo progetto realizza
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.



