ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

Creato da

Woody

6. ottobre 2026NO
27
0
0
0
0

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Intermedio
About 4 hours

Istruzioni

1

Sheet speed from the slot

Caricamento del notebook Jupyter…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

Materiali per questo passaggio:

SpazzoloneSpazzolone1 pezzo

Strumenti necessari:

Morsa da bancoMorsa da banco
Trapano a batteriaTrapano a batteria
Serie di punte da trapanoSerie di punte da trapano
Sega da traforoSega da traforo
Pennarello indelebilePennarello indelebile
RighelloRighello
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

Strumenti necessari:

Serie di scalpelli da legnoSerie di scalpelli da legno
MartelloMartello
Calibro digitale da 6 polliciCalibro digitale da 6 pollici
Taglierino di precisioneTaglierino di precisione
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

Materiali per questo passaggio:

Tubo di rameTubo di rame1 pezzo
Raccordi in ottoneRaccordi in ottone1 pezzo

Strumenti necessari:

TagliatubiTagliatubi
Lime (lima a mano)Lime (lima a mano)
Chiave regolabile a rullinoChiave regolabile a rullino
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

Materiali per questo passaggio:

Sigillante siliconicoSigillante siliconico1 pezzo
Foglio di gommaFoglio di gomma1 pezzo
Lamiera di alluminioLamiera di alluminio1 pezzo
Vite da legno #8 x 1"Vite da legno #8 x 1"1 pezzo

Strumenti necessari:

Cesoie da lattoniereCesoie da lattoniere
Set di cacciavitiSet di cacciaviti
Taglierino di precisioneTaglierino di precisione
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

Materiali per questo passaggio:

Tubo di rameTubo di rame1 pezzo
Valvola a sferaValvola a sfera1 pezzo
Raccordi in ottoneRaccordi in ottone1 pezzo
Nastro di PTFE per filettiNastro di PTFE per filetti1 pezzo
Barattolo di lattaBarattolo di latta1 pezzo
Sigillante siliconicoSigillante siliconico1 pezzo

Strumenti necessari:

TagliatubiTagliatubi
Chiave regolabile a rullinoChiave regolabile a rullino
Trapano a batteriaTrapano a batteria
Serie di punte da trapanoSerie di punte da trapano
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
Passo 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
Passo 10 - Image 1

Materiali per questo passaggio:

AcquaAcqua1 pezzo

Strumenti necessari:

Brocca graduataBrocca graduata
CronometroCronometro
RighelloRighello
Tubo da giardinoTubo da giardino
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

Materiali

11

Strumenti richiesti

18

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...