ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Youblob (generated from this blueprint's notebook) · CC0
The Spool Valve: Steering Oil With a Sliding Rod
A pump makes flow and a cylinder makes force. Between them sits the valve that decides where the oil goes: to one end of the cylinder, to the other, or back to the tank. In almost every hydraulic machine that valve is a **spool**: a ground steel rod with raised lands, sliding in a bore with five ports — pressure, tank, two work ports, and a second tank.
Slide the spool one way and pressure goes to port A while B drains; slide it the other way and the roles swap; centre it and the ports are blocked or joined, depending on the spool's centre. The edges of the lands are orifices, so the spool also meters how fast.
This rung works out the metering, the choice between open and closed centre, and builds a transparent spool valve that shows the oil paths in coloured water.
Intermedio
About 4 hours
Istruzioni
1
1
Metering edges and the centre condition
Metering edges and the centre condition
Caricamento del notebook Jupyter…
2
2
Each land edge is a throttle
Each land edge is a throttle
The spool meters flow the way any restriction does. The embedded blueprint shows how flow through a restriction depends on its area and the pressure across it.
3
3
Build a clear spool valve
Build a clear spool valve
Take 150 mm of clear acrylic tube with a smooth 20 mm bore. Drill five 6 mm holes in a line along one side, 20 mm apart, and glue a hose barb over each: from one end, **T**, **A**, **P**, **B**, **T**.
3D-print a spool: a 10 mm shaft carrying three lands, each 12 mm long with an O-ring groove, spaced so that when the spool is centred the middle land exactly covers **P** and the outer lands cover **A** and **B**. Fit O-rings sized to seal lightly in the bore. A handle on one end, a stop on the other.
Connect **P** to a garden hose through a ball valve, the two **T** ports to a bucket, and **A** and **B** to the two ports of the double-acting cylinder, or to two clear tubes standing up so you can see which one fills.
Materiali per questo passaggio:
Tubo acrilico (trasparente)1 pezzo
Assortimento di raccordi in PVC1 pezzo
Assortimento di O-ring1 pezzo
Tubo in silicone2 metri
Distributore idraulico1 pezzoStrumenti necessari:
Stampante 3D a filamento (FDM)
Filamento PETG
Trapano a batteria
Serie di punte da trapano
Calibro digitale da 6 pollici
Pistola per colla a caldo
Secchio4
4
The three positions
The three positions
Spazio di lavoro Blockly
Loading Blockly workspace...
5
5
Run it with coloured water
Run it with coloured water
Add food colouring to a bucket feeding a small submersible pump, or tint the hose supply with a dye injector, so the flow shows in the clear bore.
Centre the spool and open the supply: nothing moves, and the supply hose stiffens — that is a closed centre. Slide the spool slowly one way: first a thread of colour as the edge just cracks open, then a full stream into **A** while **B** drains to **T**. Slide it the other way and watch the paths swap.
Then turn the middle land down on a second printed spool so that, centred, it leaves a gap round **P**: now the supply runs straight through to **T** at the centre. That is an open centre.
Materiali per questo passaggio:
Colorante alimentare (colorante per la visualizzazione del flusso)1 pezzo
Acqua20 litriStrumenti necessari:
Pompa sommersa
Cronometro6
6
A valve that will not control the load
A valve that will not control the load
Directional valve faults, in the order to check them.
Flow
Loading...
7
7
Context and honest limits
Context and honest limits
Spool valves go back to the steam age — slide valves on engines, piston valves on locomotives — and became the standard directional valve of oil hydraulics. Their symbols and port letters (P, T, A, B) are now standardised, so a circuit diagram from any maker reads the same way.
**Honest limits.** A spool always leaks a little through its clearance, so it cannot hold a load for long; a check valve does that. Flow through the edges also pushes on the spool (flow forces), which is why large valves are moved by pilot pressure rather than by hand. The printed model with O-rings shows the paths, not the metering: real spools seal by a micrometre clearance, not by rubber.
Materiali
7- 1 pezzoSegnaposto
- Segnaposto
- 1 pezzoSegnaposto
- 2 metriSegnaposto
- 1 pezzoSegnaposto
- Segnaposto
- 20 litriSegnaposto
Strumenti richiesti
9- Segnaposto
- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi
Throttling: Letting Some of It Past
di Emma
Meccanica
7
0
0
0
0
0
Orifice Plate Meter
di Emma
TECNOLOGIA
37
0
0
0
0
0
One Way Only: The Check Valve and the Bang It Makes
di Martin
Utensili
13
0
0
0
0
0
Safety Relief Valve
di Penny
TECNOLOGIA
41
0
0
0
0
0
O-Ring Seal
di Mary
Lavorazione dei metalli
49
0
0
0
0
0
Hydraulic Accumulator
di Emma
Lavorazione dei metalli
34
0
0
0
1
0
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.