コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)
Forge

作成者

Forge

14. 11月 2026NO
9
0
0
0
0

Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)

George Edwinson's tong-making lesson from Amateur Work (1886): jaws forged from inch-square iron, reins of 5/8 in. rod scarfed and welded on, the halves riveted with a hot iron pin. The same flat-bit tongs are then reshaped into pincer, hammer and crook-bit tongs, light smith's pliers, and thinned and curved into crucible tongs.
上級者
A day at the forge

手順

1

His sizes

Jupyter ノートブックを読み込み中…
2

Read Edwinson

"Indeed, the man who can turn out a good pair of tongs may be trusted with almost any job in the smithy."
3

Forge the reins

Cut two pieces of 5/8 in. (16 mm) iron rod, each 2 ft (0.6 m) long, with a cold chisel. Bring one end of each to a white welding heat and draw 3-4 in. down to a taper from 5/8 to 1/2 in., rounded for the hand. Upset the other ends at a white heat and scarf them (his figs. 27-28).

このステップの材料:

錬鉄の棒錬鉄の棒1 個

必要な工具:

たがねたがね
鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
鍛冶やっとこ鍛冶やっとこ
4

Forge the jaws

Cut two 6 in. pieces of 1 in. square iron (or one 12 in. bar, worked from each end before cutting, fig. 29). Forge each jaw end 4 in. long, 1 1/4 in. wide and 3/8 in. thick. Flatten the other end to 1/4 in. thick, round it for the joint (fig. 30) and draw it to a slightly rounded taper (fig. 31).

このステップの材料:

軟鋼角棒軟鋼角棒1 個

必要な工具:

鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
鍛冶やっとこ鍛冶やっとこ
5

Punch the joint

Mark the hole with a centre punch, heat, and punch a 3/8 in. hole over the anvil's heel hole with an iron punch tapering 1/4 to 1/2 in. (fig. 35), or a steel punch of 5/8 in. tool steel.

このステップの材料:

工具鋼丸棒工具鋼丸棒1 個

必要な工具:

センターポンチセンターポンチ
鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
6

Weld jaw to rein

Scarf the taper end of each jaw to fit a rein. Heat both to a welding heat in a clear fire, throw on clean fine fresh-water sand and heat until pasty. Tap the scarfs together lightly, return to the fire a moment, and finish the weld. At a red heat forge the square part to blend into the round rein (fig. 32).

このステップの材料:

砂砂1 個

必要な工具:

鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
鍛冶やっとこ鍛冶やっとこ
7

Rivet the joint

Smiths' way: nick a 3/8 in. round iron rod to rivet length, put the halves together, insert the hot end, twist it off, let 1/4 in. stand below, and rivet both sides. (Or make a 3/4 x 3/8 in. button-headed rivet in a 3/8 in. hole in a flat iron.) If the joint locks, reheat jaws and pin to bright red and work them free.

このステップの材料:

錬鉄の棒錬鉄の棒1 個

必要な工具:

鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
釘頭台釘頭台
8

Set the jaws

Heat the jaws and set them to the width of the stock to be held. Spring them wider with a piece of cold iron between and a few light blows.

必要な工具:

鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
9

Crucible tongs and other forms

From flat-bit tongs at the fig. 32 stage: lengthen and curve the bits for pincer tongs (angular notches hold round or square bars), more for hammer tongs, bend them sideways for crook-bit tongs. Small flat-bit tongs with lengthened, shaped bits are smith's pliers; thin those out further and curve them like pincers to make crucible tongs for hot crucibles and pots of molten metal. Heavy tongs 2-5 ft long need stouter iron.

必要な工具:

鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
鍛冶やっとこ鍛冶やっとこ
10

Troubleshooting

Tongs troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" III, **Amateur Work, Illustrated**, vol. V (1886), pp. 266-269 (checked on the archive.org scan amateurworkillus05lond). He gives full sizes only for the flat-bit tongs; crucible tong sizes and curvature are left to the work. Metric figures and tools are ours.

材料

4
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • 1 個
    プレースホルダー

必要な工具

7

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...