コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)
Forge

作成者

Forge

4. 11月 2026NO
12
0
0
4
0

Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)

An above-ground oil tank of riveted 'tank steel': a flat bottom, rings of plate lapped and riveted, angle irons at top and bottom, and a self-supporting globe roof. Every seam is caulked oil-tight and the tank is water-tested before painting. Variable: capacity. Bell's Fig. 158 is 1,000 barrels: 20 ft inside diameter, about 20 ft 3 in high, four rings of 1/4 in plate, sixteen 3/16 in roof plates rising 3 ft. Standard tanks run from 500 to 80,000 barrels (120 ft x 40 ft). Source: H. S. Bell, American Petroleum Refining (1923), pp. 286-306. Picture: Fig. 158 of the book.
エキスパート
Unknown

手順

1

Choose the size and plates

Pick the capacity from the standard sizes (1,000 barrels: 20 ft diameter, 20 ft high). Take plate thickness from Bell's chart for the head and diameter, with a factor of safety of at least 2 1/2 for refinery tanks. Use at least 1/4 in for the shell; bottom 1/4 in on larger tanks, 3/16 in on smaller. Rings are 6 ft (72 in plates); about 7 ft is the limit.

必要な工具:

不明な寸法不明な寸法
2

Prepare the ground

Level the ground in a circle 10 ft wider than the tank and remove all vegetable growth. Avoid a mix of cut and fill. In old yards filled with cinders, dig them out at least 8 in deep and replace with fine gravel, loam or sand. On poor soil, use piles.

このステップの材料:

砂利砂利1 as needed

必要な工具:

不明な寸法不明な寸法
3

Punch and scarf the plates

Punch the rivet holes. For 1/4 in plate with 5/8 in rivets, a single lap seam has holes 2 1/4 in apart and 1 1/8 in from the edge; keep the clear space between holes no more than 6 or 7 times the plate thickness, or the caulked edge springs. Scarf the corner of the middle plate where three plates meet: cold up to 1/4 in, hot above, drawn to an edge no thicker than 1/16 in.

必要な工具:

パンチプレスパンチプレス
大ハンマー大ハンマー
4

Build the bottom on horses

Lay, rivet and caulk the bottom on trestles or horses about 30 in high. Rivet the bottom angle iron (Fig. 158: 3 x 3 x 5/16 in) with a 1/4 in bent-plate shoe behind each angle splice; caulk the shell leg past the shoe at least 12 in, or better bevel and caulk the angle all round. Assemble and drive the first ring while the bottom is still up. Test the bottom under 6 to 8 in of water. Coat its underside with ship-bottom or heavy asphalt paint.

このステップの材料:

軟鋼板軟鋼板1 bottom, first ring
軟鋼の山形鋼軟鋼の山形鋼1 bottom angle
鋼製リベット鋼製リベット1 個
不明な材料不明な材料1 asphalt paint

必要な工具:

リベットハンマーリベットハンマー
穴広げポンチ穴広げポンチ
水水
幅広の刷毛幅広の刷毛
5

Lower it and raise the shell

Raise the tank on jacks round the edge, clear out the horses and debris, and lower the bottom to grade. Rivet and caulk the remaining rings from scaffolds: floating scaffolds where water is at hand (water is pumped in as each ring is caulked tight, testing as you go), or brackets bolted through punched holes, later plugged with hot rivets. Where three plates meet, bolt them, heat cherry red with an oil-burning torch and lay the joint up with sledges before riveting. Fit the top angle (2 1/2 x 2 1/2 x 5/16 in) and a flanged steel manhole in the bottom ring.

このステップの材料:

軟鋼板軟鋼板1 rings
軟鋼の山形鋼軟鋼の山形鋼1 top angle
鋼製リベット鋼製リベット1 個

必要な工具:

ねじジャッキねじジャッキ
リベットハンマーリベットハンマー
穴広げポンチ穴広げポンチ
松明松明
大ハンマー大ハンマー
水水
6

Fit the globe roof

For tanks up to 54 ft across, rivet on a self-supporting globe roof of segmental 3/16 in plates (Fig. 158: sixteen plates, 1/4 in centre plate, 3 ft rise); cold riveting is fine here. Make it gas-tight, with one vent at the apex covered by brass or monel wire cloth of at least 50 mesh.

このステップの材料:

軟鋼板軟鋼板1 roof
鋼製リベット鋼製リベット1 個

必要な工具:

リベットハンマーリベットハンマー
7

Test and paint

Fill the tank with water to test it before painting; it shows the important leaks, though not always tightness for light oils. Wire-brush off mill scale and rust. Give shell and roof three coats: one of red lead ground in boiled linseed oil, then two of good grey graphite paint.

このステップの材料:

鉛丹鉛丹1 first coat
ボイル亜麻仁油ボイル亜麻仁油1 個
不明な材料不明な材料2 grey graphite paint

必要な工具:

水水
ワイヤーブラシセットワイヤーブラシセット
幅広の刷毛幅広の刷毛

材料

7

必要な工具

10

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...