コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)
Forge

作成者

Forge

4. 11月 2026NO
8
0
0
1
0

Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)

A tinsmith's garden watering can: a round body from one sheet 2 ft 1 in x 8 1/2 in, a two-piece spout with a perforated rose, a hollowed top with a cross handle, and a back handle with a thumb ring. Tinplate or galvanised iron. Variable: the rose. Its pattern diameter is the rose diameter x 4 / 3; finer holes for seedlings. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 54-57. Unknown: solder. Picture: Figs. 132-135 of the book.
中級者
Unknown

手順

1

Make the body and bottom

Cut a sheet 2 ft 1 in by 8 1/2 in. Wire one edge, sink it in the crease iron, round it and groove the seam; solder the seam inside. Cut the spout hole opposite the seam, 2 1/2 in from the bottom. Edge the bottom to fit, beat it up and solder it from inside.

このステップの材料:

ブリキ板ブリキ板1 body, bottom
鉄の針金鉄の針金1 edge
錫鉛はんだ錫鉛はんだ1 個

必要な工具:

金切りばさみ金切りばさみ
杭杭
木槌木槌
電気はんだごて電気はんだごて
フラックスフラックス
2

Make and fit the spout

Cut the spout in two pieces (Fig. 133), bend them to shape and solder the seams. Solder the larger piece into the body. Make it longer for plants out of reach, with an elbow for plants up high. Make the stay: a taper strip as long as the gap between can and spout, bent to a half-round section and soldered in.

このステップの材料:

ブリキ板ブリキ板1 spout, stay
錫鉛はんだ錫鉛はんだ1 個

必要な工具:

金切りばさみ金切りばさみ
杭杭
電気はんだごて電気はんだごて
フラックスフラックス
3

Make the rose

Set out the rose body (Fig. 135): its diameter is the rose diameter x 4 / 3, so a 3 in rose needs a 4 in pattern, with lines a b at right angles. Bend it over a funnel stake and solder the seam. Hollow a disc for the front, with edges for capping on. Inside the hollow, mark circles and pierce them at intervals with a bradawl over a hard wood block; very fine for seedlings. Solder front and stem to the rose body. Several roses of different sizes are useful.

このステップの材料:

ブリキ板ブリキ板1 rose
錫鉛はんだ錫鉛はんだ1 個

必要な工具:

ディバイダー(両脚規)ディバイダー(両脚規)
金切りばさみ金切りばさみ
杭杭
均し槌均し槌
目打ち(キリ)目打ち(キリ)
堅木のブロック堅木のブロック
電気はんだごて電気はんだごて
フラックスフラックス
4

Fit the top and handles

Hollow the top (Fig. 134), fit it to the body, wire its inner arc and solder it on. Cross handle: a strip about 1 3/4 in wide, wired with No. 12 B.W.G., bent to shape; cut two holes in the top with a small sharp chisel and solder the ends inside and on top. Back handle (Fig. 136): wire and bend it, solder a small boss under its upper part, and solder it opposite the spout with a thumb ring at the top. Solder three small hollowed studs under the bottom.

このステップの材料:

ブリキ板ブリキ板1 top, handles, studs
鉄の針金鉄の針金1 No. 12 B.W.G.
錫鉛はんだ錫鉛はんだ1 個

必要な工具:

金切りばさみ金切りばさみ
均し槌均し槌
鋼の鏨鋼の鏨
電気はんだごて電気はんだごて
フラックスフラックス
5

Clean and paint

Clean with turpentine and whiting. Give two good coats of paint: red inside and green outside suit it.

このステップの材料:

油絵具油絵具2 coats

必要な工具:

テレビン油テレビン油
炭酸カルシウム(胡粉状の白亜)炭酸カルシウム(胡粉状の白亜)

材料

4

必要な工具

12

この設計図で作るもの

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...