Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Coasting Toboggan: Four Steamed Hardwood Boards Bent Over a Log Form (Boy Mechanic, 1919)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
7
0
0
0
0

Coasting Toboggan: Four Steamed Hardwood Boards Bent Over a Log Form (Boy Mechanic, 1919)

A. M. Parker's toboggan from The Boy Mechanic, Book 3 (1919), 7-1/2 ft long and 16 in wide: four 5/16 in hardwood boards steamed at one end and bent round a 12 in log on a simple form, held by notched cross cleats, the curl riveted and wired, and a rope run along the sides.
Kati
About 1 week (four days drying)

Maagizo

1

His mill bill in centimetres

Inapakia daftari la Jupyter…
2

Read The Boy Mechanic, Book 3

"Essentials of a good toboggan, whether for coasting or use in transportation, are strength and lightness." Woods in order of merit: hickory, birch and oak (not quarter-sawed).
3

Prepare the boards and cleats

Choose four 5/16 by 4 in by 10 ft boards straight in grain and free from knots. Plane the running side and bevel the edges so that, together, they form a wide V joint half the depth of the boards. Notch the seven 1 by 1 in cross cleats on one side, 1 in from each end, for the side ropes.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu4 vipande

Zana zinazohitajika:

Randa ya mkonoRanda ya mkono
Msumeno wa mkonoMsumeno wa mkono
PatasiPatasi
PenseliPenseli
Tepi ya kupimiaTepi ya kupimia
4

Build the bending form

Bore a gimlet hole through the centre of each 1 by 2 by 18 in piece and two more 4-1/4 in each side of it. Nail one 6 ft common board to each end of the 12 in by 18 in log block so their ends run parallel. With 3 in nails fix one bored cleat to the block between them, held out 1/2 in by a temporary spacer.

Vifaa kwa hatua hii:

Ubao wa msonobariUbao wa msonobari2 vipande
MisumariMisumari1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkonoKekee cha mkono
NyundoNyundo
5

Steam and bend

Steam about 3 ft of the board ends, or boil them in a tank. Clamp or nail the dry ends together edge to edge between two of the 1 by 2 in pieces, about 1/4 in apart. Push the steamed ends under the cleat on the block (its nails slip between the boards), bear down and nail on another bored cleat as far as the floor allows. Turn it over and bend the boards round the block, nailing on more cleats, until the clamped end lies between the 6 ft boards; hold it with a piece nailed across. The closer the cleats, the less risk of splitting.

Vifaa kwa hatua hii:

MisumariMisumari1 kipande

Zana zinazohitajika:

Sufuria KubwaSufuria Kubwa
NyundoNyundo
Kibano cha upauKibano cha upau
6

Fit the cleats and finish

Dry at least four days on the form. Clamp the two 1/2 by 1 in pieces on each side of the bow ends, drill through and rivet them. Rivet a 1 by 1 in crossbar inside the bow at the extreme front and another under the end of the curl, and wire them together to hold the bend. Put the tail crossbar not nearer than 2-1/2 in from the board ends and space the rest evenly, notched side down. Trim, scrape and sandpaper the bottom, finish with oil, and run a 3/8 in rope through the notches under the cleat ends.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande
Rivet za chuma cha puaRivet za chuma cha pua1 kipande
Waya wa chuma uliovutwa kwa bambaWaya wa chuma uliovutwa kwa bamba1 kipande
Mafuta ya KitaniMafuta ya Kitani1 kipande
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)1 kipande
Kamba nene ya pambaKamba nene ya pamba1 kipande

Zana zinazohitajika:

Kekee cha mkonoKekee cha mkono
NyundoNyundo
Msumeno wa mkonoMsumeno wa mkono
Kikwaruzi cha chumaKikwaruzi cha chuma
Koleo la Mdomo BapaKoleo la Mdomo Bapa
7

Troubleshooting

Toboggan troubleshooting.

Flow

Loading...
8

History and honest limits

From "Making a Coasting Toboggan" by A. M. Parker, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 11-13). The tools and metric figures are ours.

Vifaa

8

Zana Zinazohitajika

11

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...