Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
6
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
Juu
About 1-2 weeks

Maagizo

1

His sizes, and the pulley speeds

Inapakia daftari la Jupyter…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu2 vipande
Parafujo za mbaoParafujo za mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Randa ya mkonoRanda ya mkono
Kekee cha mkonoKekee cha mkono
Tepi ya kupimiaTepi ya kupimia
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara2 vipande
Nati ya pembe sitaNati ya pembe sita2 vipande
Parafujo za mbaoParafujo za mbao1 kipande
MisumariMisumari1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
PatasiPatasi
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Kekee cha mkonoKekee cha mkono
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande
Mirija ya chumaMirija ya chuma1 kipande
Shaft CollarShaft Collar4 vipande
Rivet za chuma cha puaRivet za chuma cha pua1 kipande
Neli ya shaba nyeupeNeli ya shaba nyeupe1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Seti ya kukata nyuzi za skrubuSeti ya kukata nyuzi za skrubu
Kekee cha mkonoKekee cha mkono
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kibano cha meza ya kaziKibano cha meza ya kazi
NyundoNyundo
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Kekee cha mkonoKekee cha mkono
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

Vifaa kwa hatua hii:

Ufito mviringo wa chuma lainiUfito mviringo wa chuma laini1 kipande
Fito ya chuma cha zanaFito ya chuma cha zana1 kipande
Skrubu ya kubana yenye ncha ya kikombeSkrubu ya kubana yenye ncha ya kikombe1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha mkonoKekee cha mkono
Kipanua tunduKipanua tundu
Seti ya kukata nyuzi za skrubuSeti ya kukata nyuzi za skrubu
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kibano cha meza ya kaziKibano cha meza ya kazi
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu2 vipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara5 vipande
Nati ya pembe sitaNati ya pembe sita2 vipande
Mirija ya chumaMirija ya chuma1 kipande
Fito ya chuma cha zanaFito ya chuma cha zana1 kipande
Rivet za chuma cha puaRivet za chuma cha pua1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
PatasiPatasi
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Kekee cha mkonoKekee cha mkono
Jiko la mgongo la makaa ya maweJiko la mgongo la makaa ya mawe
FuaweFuawe
Nyundo ya mhunziNyundo ya mhunzi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara1 kipande
Nati ya pembe sitaNati ya pembe sita1 kipande
Parafujo za mbaoParafujo za mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
PatasiPatasi
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

Vifaa

12

Zana Zinazohitajika

15

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...