Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
7
0
0
0
0

Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)

Part II of Stillman Taylor's rod-making series (The Boy Mechanic, Book 2, 1915): once the one-piece casting rod is mastered, the same planing, grasp and finishing methods make jointed rods. He gives full caliper tables and fitting lists for six rods; choose one in the notebook. Sections join with welted, shouldered ferrules, and every rod gets two tips "in view of a possible breakage".
Juu
About 2-3 weeks (glue and varnish drying)

Maagizo

1

His caliper tables

Inapakia daftari la Jupyter…
2

Read The Boy Mechanic, Book 2

"While the action of the one-piece rod is undeniably better than when the rod is made in two or three pieces, it is less compact to carry." He warns that "the more joints incorporated in a rod, the less satisfactory it will be from an angling standpoint", since ferrules cannot follow the rod's curve.
3

Choose the rod and get the stock

Pick a rod from the notebook. Stock (dagame or greenheart): two-piece casting -- butt 5/8 in x 3 ft, two tips 3/8 in x 3 ft; three-piece casting -- all 2 ft, butt 5/8 in, joint and tips 3/8 in; trout or bass fly -- butt 5/8 in x 4 ft, joint and tips 3/8 in x 4 ft; salt-water -- both 4 ft, butt 3/4 in, tip 1/2 in; tarpon -- one piece 1 in x 6-1/2 ft.

Vifaa kwa hatua hii:

Mbao ya dagameMbao ya dagame4 vipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Tepi ya kupimiaTepi ya kupimia
4

Plane each section to its table

Plane, round and scrape each section exactly as for the one-piece rod, calipering at every station in the table. Two-piece casting rod: he first suggests a butt of about 23 in and a 32-1/2 in tip to fit a 35 in rod case, then specifies a 6-1/2 oz rod with a 32-1/2 in butt (15/32 in at the grasp to 19/64 in at the ferrule) and a 33 in tip (17/64 in to 7/64 in), equal when ferrule and top are on. Make two tips for each rod.

Vifaa kwa hatua hii:

Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)1 kipande

Zana zinazohitajika:

Randa ya mkonoRanda ya mkono
Randa ndogo ya kiganjaRanda ndogo ya kiganja
Kikwaruzi cha chumaKikwaruzi cha chuma
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kalipa ya VernierKalipa ya Vernier
5

Fit the ferrules

Fit a welted, shouldered ferrule at each joint, sized from his list: 17/64 in for the two-piece casting rod; 21/64 in and 15/64 in for the three-piece; 9/32 in and 11/64 in for the fly rods; 7/16 in for the salt-water rod; a 3/4 in male ferrule on the tarpon butt. The tip ferrule comes with two closed-end centres, one for each tip. Cement them on with ferrule cement; serrated (toothed) ferrule ends are wound with silk for strength.

Vifaa kwa hatua hii:

Feruli ya fimboFeruli ya fimbo2 vipande
Gundi ya feruliGundi ya feruli1 kipande
Hariri ya kuzongea fimboHariri ya kuzongea fimbo1 kipande

Zana zinazohitajika:

Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Tochi ya PropaniTochi ya Propani
Kalipa ya VernierKalipa ya Vernier
6

Build the grasp and reel seat

Build the cork grasp and reel seat as for the one-piece rod: 3/4 in reel seat with straight hood for the casting rods (fly-rod type with butt cap on the fly rods, 9 in or 9-1/2 in of cork above it), 7/8 in on the salt-water rod with an 18 in double grasp, 1 in on the tarpon rod. Use a 1 in butt cap (1-1/8 in on the tarpon rod) and a taper (winding check) of the small-end size in his list. For an independent butt, fit the ferrule straight on a rounded dagame core so the seated ferrule does not touch the wood, cement and rivet it, fit a soft-pine sleeve over core and ferrule, glue it on, cement and rivet the reel seat, then glue on the corks and cut the core flush.

Vifaa kwa hatua hii:

Pete za kiziboPete za kizibo24 vipande
Gundi ya wanyamaGundi ya wanyama1 kipande
Ubao wa msonobariUbao wa msonobari1 kipande
Kishikio cha reliKishikio cha reli1 kipande
Kifuniko cha kitako cha fimboKifuniko cha kitako cha fimbo1 kipande
Pete ya kumalizia mshikoPete ya kumalizia mshiko1 kipande
Gundi ya feruliGundi ya feruli1 kipande
Rivet za shabaRivet za shaba1 kipande

Zana zinazohitajika:

Kisu cha kazi za mikonoKisu cha kazi za mikono
Kekee cha mkonoKekee cha mkono
Randa ndogo ya kiganjaRanda ndogo ya kiganja
Tochi ya PropaniTochi ya Propani
NyundoNyundo
7

Mount the guides and tops

Casting rods: two 1/2 in narrow agate guides, two No. 1 one-ring casting guides and two 3/32 in offset agate tops. Fly rods: two No. 4 snake guides on the butt joint, three No. 3 on the middle joint, three No. 2 on each tip, and two No. 7 agate angle fly tops of the wind-on kind. Salt-water rod: a 10/32 in stirrup-tube agate top and two No. 3 bell guides. Tarpon rod: two No. 11 wide raised agate guides, two No. 1 trumpet guides and a 3/8 in agate stirrup top; whip its guides on double, the first set 10 in from the top, the second 26 in from the reel. Whip with 00 silk (00 or 0 on the three-piece rod, size A on the salt-water and tarpon rods), using the invisible knot.

Vifaa kwa hatua hii:

Pete ya kuongoza uzi wa fimboPete ya kuongoza uzi wa fimbo8 vipande
Pete ya ncha ya fimboPete ya ncha ya fimbo2 vipande
Hariri ya kuzongea fimboHariri ya kuzongea fimbo1 kipande
Nta ya NyukiNta ya Nyuki1 kipande

Zana zinazohitajika:

Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kisu cha kazi za mikonoKisu cha kazi za mikono
8

Shellac and varnish

Shellac the windings and varnish the rod with coach varnish as for the one-piece rod: thin coats, warm, three days between coats.

Vifaa kwa hatua hii:

Vanishi ya shelakiVanishi ya shelaki1 kipande
Varnishi ya magari ya farasiVarnishi ya magari ya farasi3 vipande

Zana zinazohitajika:

Brashi pana ya rangiBrashi pana ya rangi
9

Troubleshooting

Jointed rod troubleshooting.

Flow

Loading...
10

History and honest limits

From "Fishing-Rod Making and Angling, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 69-72). Two points are given as he wrote them: the two-piece casting rod's butt is about 23 in in one sentence and 32-1/2 in in the next; the three-piece rod's stock is "2 ft. long" while its finished sections are 21-1/2, 21-3/4 and 21 in. Guide counts in the list are for the fly rods, the largest set. The tools and metric figures are ours.

Vifaa

17

Zana Zinazohitajika

12

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...