Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Imeundwa na

Forge

13. Novemba 2026NO
3
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Kati
8-15 minutes a pair, once practised

Maagizo

1

Bar length and sizes

Inapakia daftari la Jupyter…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Tepi ya kupimiaTepi ya kupimia
PenseliPenseli
Karatasi nzitoKaratasi nzito
Fua ya mhunziFua ya mhunzi
Patasi ya kukata kwenye fuawePatasi ya kukata kwenye fuawe
Koleo la forjiKoleo la forji
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Fuawe ndogo yenye mdomoFuawe ndogo yenye mdomo
Gari la KuburutaGari la Kuburuta
Nyundo ya kuzungushaNyundo ya kuzungusha
Koleo la forjiKoleo la forji
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Zana zinazohitajika:

Fuawe ndogo yenye mdomoFuawe ndogo yenye mdomo
Nyundo ya kuzungushaNyundo ya kuzungusha
Koleo la forjiKoleo la forji
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Zana zinazohitajika:

Fuawe ndogo yenye mdomoFuawe ndogo yenye mdomo
Fuller (chombo cha kuchora mifereji)Fuller (chombo cha kuchora mifereji)
Gari la KuburutaGari la Kuburuta
Nyundo ya kuzungushaNyundo ya kuzungusha
Koleo la forjiKoleo la forji
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Zana zinazohitajika:

Fuawe ndogo yenye mdomoFuawe ndogo yenye mdomo
Kitoboa cha motoKitoboa cha moto
Kitoboa mashimo ya misumari ya farasiKitoboa mashimo ya misumari ya farasi
Nyundo ya kuzungushaNyundo ya kuzungusha
Koleo la forjiKoleo la forji
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Fuawe ndogo yenye mdomoFuawe ndogo yenye mdomo
Nyundo ya kuzungushaNyundo ya kuzungusha
Fuller (chombo cha kuchora mifereji)Fuller (chombo cha kuchora mifereji)
Kitoboa cha motoKitoboa cha moto
Kitoboa mashimo ya misumari ya farasiKitoboa mashimo ya misumari ya farasi
Koleo la forjiKoleo la forji
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Vifaa

1

Zana Zinazohitajika

12

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...