Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
9
0
0
0
0

Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)

Joseph Moxon's 1677 way to make the screw bolt for a door: a square iron bar forged down to a square neck and round pin, the head cut off with a chisel, the pin threaded with a screw-plate, and a punched iron nut threaded with a tap. The square neck sits in a square hole so the bolt cannot turn while the nut is tightened.
Kati
About an hour per bolt

Maagizo

1

Choosing the hole

Inapakia daftari la Jupyter…
2

Read Mechanick Exercises

"The Shank of the Screw for Doors and many other purposes must be Forged square near the Head, because it must be let into a square hole that it may not twist about when the Nut is turned about hard upon the Screw-Pin."
3

Forge the square neck

Take a square iron bar as near the size of the head as you can. At a flame (white) heat lay the shank length flat on the near side of the anvil and hammer it down to thickness; do not strike over the edge or you cut the iron. Reheat, turn it, and hammer the other two sides close up to the head.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
4

Round the pin, cut the head

Hammer down the corners of the part meant for the thread and round it. Set the chisel at the head thickness, strike half through, turn and cut each side half through until it comes off. Square the shoulder: reheat, grip in square-nosed tongs, set the shank in the vice with the shoulder on the jaws, and hammer the head.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Patasi ya kukata kwenye fuawePatasi ya kukata kwenye fuawe
Koleo za mhunziKoleo za mhunzi
Kibanio kizito cha meza ya kaziKibanio kizito cha meza ya kazi
NyundoNyundo
5

Punch the nut

Forge a nut blank from the bar. Harden the point of a steel punch of the hole's size (no tempering: the hot iron softens it). At a blood-red heat punch from one side until the far side bulges, turn it, set it flat, and punch through over the hole of a bolster. Dip the punch in water whenever it changes colour. Let forged work cool on the floor or hearth; never quench it.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Kitoboa cha motoKitoboa cha moto
NyundoNyundo
Ndoo ya kupoza chumaNdoo ya kupoza chuma
Koleo za mhunziKoleo za mhunzi
6

Thread the pin

File the shank and head, file the pin round, and taper its end by the depth of the screw-plate's threads. Find the screw-plate hole the pin just slides through, turn the pin in it, and file off the marks it cuts: the pin is then true. Set the bolt head down in the vice, press the next smaller hole (groove diameter equal to the pin) hard down on it, and turn the plate evenly.

Zana zinazohitajika:

Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kibanio kizito cha meza ya kaziKibanio kizito cha meza ya kazi
Seti ya kukata nyuzi za skrubuSeti ya kukata nyuzi za skrubu
7

Tap the nut

Fit the tap to the round hole of the nut; it must match the pin (try it in the same screw-plate hole). Set the nut flat in the vice and turn the tap hard round by its handle, or by the square hole near the screw-plate handle, until it cuts the thread.

Zana zinazohitajika:

Kibanio kizito cha meza ya kaziKibanio kizito cha meza ya kazi
Seti ya kukata nyuzi za skrubuSeti ya kukata nyuzi za skrubu
8

Troubleshooting

Screw bolt troubleshooting.

Flow

Loading...
9

History and honest limits

From Joseph Moxon, **Mechanick Exercises, or the Doctrine of Handy-Works** (1677), Smithing, Numb. I pp. 10-11 and Numb. II pp. 29-31 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes or nut shape; the metric example and the tool heads are ours.

Vifaa

1

Zana Zinazohitajika

10

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...