Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Anvil Hole Punch: Forged C-Frame With a Steel Die Block and Top Die, Set in the Hardy Hole (Richardson, 1889)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
7
0
0
0
0

Anvil Hole Punch: Forged C-Frame With a Steel Die Block and Top Die, Set in the Hardy Hole (Richardson, 1889)

A blacksmith's anvil punch from Richardson's Practical Blacksmithing (1889): a bent C-frame of Swedish iron with a steel die block welded on, a square shank that drops into the anvil's hardy hole, and a cast-steel top die struck with a sledge. A set of six, 1/4 to 1 in, punches cold iron up to 5/16 or 3/8 in thick.
Juu
About 1 day

Maagizo

1

The set of six

Inapakia daftari la Jupyter…
2

Read Practical Blacksmithing

"I think every blacksmith should have a set of them."
3

Forge the frame and die block

Take Swedish iron 1-1/2 by 3/4 by 10 in, upset one end a little, and weld a square of good steel 1-1/2 by 1-1/2 in firmly on it. Punch a hole in the centre of the steel a little larger than the hole to be cut, driving from the iron side so the hole is largest at the bottom and the slugs drop out. Heat the other end, cut it half off 1-1/2 in from the end, bend it over and weld it, then punch and work out a perfectly true 3/4 in square hole (Fig. 68).

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande
Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo la forjiKoleo la forji
Kitoboa cha motoKitoboa cha moto
Patasi ya motoPatasi ya moto
Nyundo kubwaNyundo kubwa
4

Weld on the shank

Weld an iron the size of your anvil's square hole on the bottom side, 2-1/2 in from the round hole (Fig. 69). File and dress the piece.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
5

Make the top die

Cut 6 in of 3/4 in square cast steel, draw it down and file one end to fit the round hole; for the 1/4 in punch make the round part 5/16 in long, larger for larger punches (Fig. 70).

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Msumeno wa chumaMsumeno wa chuma
6

Bend, fit and temper

Heat the frame and bend it so the two holes line up; fit the top die and make sure it enters the hole perfectly true. Let it cool slowly, check the bottom die face and that the die works straight and easily, then temper as for any tool that cuts iron (Fig. 71).

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Ndoo ya kupoza chumaNdoo ya kupoza chuma
7

Troubleshooting

Anvil punch troubleshooting.

Flow

Loading...
8

History and honest limits

From M. T. Richardson (ed.), **Practical Blacksmithing**, vol. I (1889), "Making an Anvil Punch" by N. C. M. (checked on the archive.org scan practicalblacksm00richrich, pp. 126-128). He gives no temper colour; the tools and metric figures are ours.

Vifaa

2

Zana Zinazohitajika

10

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...