Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)
Bubbles

Imeundwa na

Bubbles

14. Novemba 2026IT
4
0
0
0
0

Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)

Alfred Soward's lampwork bulb pipette from Amateur Work (1886), made like his thistle funnel: a 3/8 in. bore tube closed and drawn down onto a 1/8 in. stem, blown into a bulb, a thin second bulb blown and broken off the far side to leave a short neck, and a second stem drawn to a fine capillary tip joined on.
Juu
An hour once the basic operations are mastered

Maagizo

1

Read Soward

"To make a pipette the process is very similar." (to the thistle funnel)
2

Prepare the tubes

Take glass tube of about 1/8 in. (3 mm) bore for the stems and about 3/8 in. (10 mm) bore for the bulb. Close the wide tube at one end in the form of his fig. 41 A, then soften it about an inch from the end and draw it down to the small tube's diameter.

Vifaa kwa hatua hii:

Mrija wa kiooMrija wa kioo1 kipande

Zana zinazohitajika:

Kichomeo cha BunsenKichomeo cha Bunsen
Mrija wa kupulizia kiooMrija wa kupulizia kioo
3

Join the first stem

Cut the drawn, flask-shaped piece off with a file and fuse it to a length of the narrow tube: soften both ends, press them together, pull gently to reduce the thickened joint, and blow a gentle stream of air in.

Vifaa kwa hatua hii:

Mrija wa kiooMrija wa kioo1 kipande

Zana zinazohitajika:

Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kichomeo cha BunsenKichomeo cha Bunsen
Mrija wa kupulizia kiooMrija wa kupulizia kioo
4

Blow the bulb

Soften the flask part and blow it into a bulb through the stem.

Zana zinazohitajika:

Kichomeo cha BunsenKichomeo cha Bunsen
Mrija wa kupulizia kiooMrija wa kupulizia kioo
5

Open the far end

Play the flame on the point opposite the stem (A in fig. 41) and blow a very thin second bulb with a strong blast. Break it away: it leaves a small projecting tube (B).

Zana zinazohitajika:

Kichomeo cha BunsenKichomeo cha Bunsen
Mrija wa kupulizia kiooMrija wa kupulizia kioo
6

Draw and join the tip

Draw a second piece of narrow tube to a capillary end: thicken it in the flame, pull the hands apart, cut with a file and hold the cut end a moment in the flame. Join this stem to the projecting tube as before.

Vifaa kwa hatua hii:

Mrija wa kiooMrija wa kioo1 kipande

Zana zinazohitajika:

Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kichomeo cha BunsenKichomeo cha Bunsen
Mrija wa kupulizia kiooMrija wa kupulizia kioo
7

Troubleshooting

Pipette troubleshooting.

Flow

Loading...
8

History and honest limits

From Alfred W. Soward, "Glass-Blowing for Amateurs" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 173-176, figs. 39-41 (checked on the archive.org scan amateurworkillus05lond). He gives no volume or graduation: calibrate it by weighing water if you need one (see the graduated-pipette blueprint). Metric figures are ours.

Vifaa

1

Zana Zinazohitajika

3

Mchoro huu unatengeneza

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...