Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

Imeundwa na

Forge

15. Novemba 2026NO
3
0
0
0
0

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
Mwanzo
An hour

Maagizo

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

Vifaa kwa hatua hii:

Neli ya shaba nyeupeNeli ya shaba nyeupe1 kipande

Zana zinazohitajika:

Kibano cha meza ya kaziKibano cha meza ya kazi
Msumeno wa chumaMsumeno wa chuma
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

Zana zinazohitajika:

Kibano cha meza ya kaziKibano cha meza ya kazi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Tupa za sindanoTupa za sindano
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

Vifaa kwa hatua hii:

Bamba la Shaba ya NjanoBamba la Shaba ya Njano1 kipande
Waya wa LehemuWaya wa Lehemu1 kipande
FluksiFluksi1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Chuma cha kulehemiaChuma cha kulehemia
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

Vifaa kwa hatua hii:

Waya wa chumaWaya wa chuma1 kipande

Zana zinazohitajika:

Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

Vifaa

5

Zana Zinazohitajika

8

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...