Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)
Forge

Imeundwa na

Forge

13. Novemba 2026NO
8
0
0
0
0

Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)

T. T. Sturgeon's hand plow from The Boy Mechanic, Book 3 (1919), "worth about $5 at an outlay of 25 cents": a 16 in wheelbarrow wheel, handles ripped from one spruce strip, iron-strap braces, an adjustable vertical strap, and a moldboard and share cut from an old shovel blade to his grid pattern.
Kati
About 1 day

Maagizo

1

His cut list in centimetres

Inapakia daftari la Jupyter…
2

Read The Boy Mechanic, Book 3

"The labor of spading a garden of even moderate size is sufficient to warrant the person who undertakes the job in making a hand plow like that shown in the illustration."
3

Make the handles

Mark both handles on a 7/8 by 4 in spruce strip 5 ft long, one curved grip at each end on opposite edges. Cut the curves with a keyhole saw, then rip the board into the two handles; smooth them and trim the grips with a sharp knife. Cut a section of broomstick for the upper brace.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande
UfagioUfagio1 kipande

Zana zinazohitajika:

Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
Msumeno wa kupasuaMsumeno wa kupasua
Kisu cha ngoziKisu cha ngozi
PenseliPenseli
4

Make the iron parts

Lower brace: iron 1/4 by 1-1/4 by 12 in, drilled for 1/4 in bolts, bent at right angles 1-1/2 in from each end, with a 1/4 in hole at the middle. Vertical support: 1/4 by 1-1/4 by 18 in, four 1/4 in adjusting holes 1 in apart at the top, three 1/4 in holes at the bottom for the moldboard, and a 5/16 in hole at the 7-1/2 in mark. Two braces 14 in long of 1/4 by 1-1/4 in, a 3/8 in hole at the front of each for the 3/8 by 10 in axle bolt and a 5/16 in hole at the other end, each 1 in from the end. Landside: 1/8 by 3/4 by 12 in.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini3 vipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha mkonoKekee cha mkono
Kibano cha meza ya kaziKibano cha meza ya kazi
NyundoNyundo
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Tepi ya kupimiaTepi ya kupimia
5

Cut the moldboard

Draw his moldboard (Fig. 4) on cardboard ruled in 1 in squares, tracing the outline square by square, and mark the bolt holes. Trace it on an old shovel blade, using the thickest part for the point of the share. Cut it out, smooth the edges and sharpen the cutting edge. Drill for 1/4 in bolts to the vertical strap and 3/16 in bolts to the landside.

Vifaa kwa hatua hii:

SepetuSepetu1 kipande
Mabamba ya kadibodi ya kielelezoMabamba ya kadibodi ya kielelezo1 kipande

Zana zinazohitajika:

PenseliPenseli
Msumeno wa chumaMsumeno wa chuma
Kisaga cha pembeKisaga cha pembe
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kekee cha mkonoKekee cha mkono
6

Shape and assemble

Curve the moldboard and fit it to the supports as in Figs. 1-3. Bend the 12 in landside strip under the moldboard and bolt it on. Assemble on the 16 in wheel and 3/8 in axle bolt, with wheel and landside in line (Fig. 2) and the landside's rear edge raised slightly (Fig. 3); set the vertical strap's height for the operator in its adjusting holes. Paint the plow and oil the smoothed cutting parts.

Vifaa kwa hatua hii:

Gurudumu la toroliGurudumu la toroli1 kipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara6 vipande
Nati ya pembe sitaNati ya pembe sita6 vipande
Washa bapaWasha bapa6 vipande
Rangi ya mafutaRangi ya mafuta1 kipande
Mafuta ya mashineMafuta ya mashine1 kipande

Zana zinazohitajika:

Kibano cha meza ya kaziKibano cha meza ya kazi
NyundoNyundo
Brashi pana ya rangiBrashi pana ya rangi
7

Troubleshooting

Garden plow troubleshooting.

Flow

Loading...
8

History and honest limits

From "Garden Plow Made of Pick-Up Material" by T. T. Sturgeon, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 227-228). The moldboard shape is his Fig. 4 grid. The keyhole saw is a coping saw here; the tools and metric figures are ours.

Vifaa

11

Zana Zinazohitajika

12

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...