SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Tilting-Tub Counter-Fan Churn: Two Fans Turn Opposite Ways, the Tub Tips to Drain and Work
Lucian A. Brown and Hubbard Bigelow, Hartford, Connecticut · Public domain (expired patent)
Martin

Imeundwa na

Martin

6. Oktoba 2026NO
33
0
0
0
0

Tilting-Tub Counter-Fan Churn: Two Fans Turn Opposite Ways, the Tub Tips to Drain and Work

Brown and Bigelow wanted one churn to make the butter and then work it, by tipping the tub on its side. Lucian A. Brown and Hubbard Bigelow of Hartford, Connecticut, received US 9,311, dated 5 October 1852, assigned to Henry K. W. Welch. Their conical tub E swings on journals between two standards. The crank turns a fan H on the shaft G; a shell with inside gear on G's lower end turns, through a small pinion u, a spur gear t on a hollow shaft round G, which carries a second fan L the opposite way. A conical tube K, of tin or any other suitable material and watertight to the tub's bottom, keeps the cream from the hollow shaft. When the butter has come, the tub is tipped about 90 degrees: the buttermilk runs out at an aperture in the cover and the turning fans knead, work and roll the butter. This rung works out the gear train, then prints the gears, inner fan and conical tube, builds the tub and frame, and makes and works butter.
Juu
About 6 hours, plus printing

Maagizo

1

The gear train

Inapakia daftari la Jupyter…
2

Gears driving more than one beater before it

The embedded blueprint drives several beaters from one crank through gears. Brown and Bigelow use an inside gear and a pinion to turn two fans opposite ways on one axis.
3

Read US 9,311

"In this horizontal position of the tub E we continue the rotation of the crank I, as in the operation of churning, and the butter thus becomes kneaded, worked and rolled, as the beater H in its revolutions scrapes the butter from the inside of the tub, while the beater L, revolving in the opposite direction, in close proximity to and inside of the other, will strike the butter forced over the beater H by the accumulation by scraping off the butter on the side of the tub, while the buttermilk and water, extracted from the butter by this process, runs down over the now inclined bottom of the tub E, and escapes by the aperture a' of the cover Z, Z, Z, into any receptacle placed under the aperture to receive it."
4

Print the parts

Print the shell gear S with 72 inside teeth, the 12-tooth stud pinion u, the 48-tooth spur gear t printed in one with the hollow shaft x, the inner fan L and the conical tube K. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Vifaa kwa hatua hii:

Uzi wa PETGUzi wa PETG1 kipande

Zana zinazohitajika:

Printa ya 3D ya nyuzi (FDM)Printa ya 3D ya nyuzi (FDM)
5

Print the shell gear

The shell gear, printed as step 4 describes.
Faili ya UsanifuSTLCC0 - Free
Pakua modeli
6

Print the stud pinion

The stud pinion, printed as step 4 describes.
Faili ya UsanifuSTLCC0 - Free
Pakua modeli
7

Print the spur gear t with the hollow shaft x

The spur gear t with the hollow shaft x, printed as step 4 describes.
Faili ya UsanifuSTLCC0 - Free
Pakua modeli
8

Print the inner fan

The inner fan, printed as step 4 describes.
Faili ya UsanifuSTLCC0 - Free
Pakua modeli
9

Print the conical tube

The conical tube, printed as step 4 describes.
Faili ya UsanifuSTLCC0 - Free
Pakua modeli
10

Tub, tube and frame

Use a tapered food-grade container about 250 mm across the top. Drill a 20 mm hole in the centre of its bottom and seal the conical tube's flange round it inside with food-safe silicone. Bolt a short carriage bolt through each side at mid-height as the journals d, with washers and silicone, and hang the tub by them in holes near the tops of two pine standards on a pine base. Screw a pine cross bar under the bottom (his q q) with a 4 mm screw standing down from it 37.5 mm off centre as the stud V, and a pine bridge below it (his n n) with a step hole for the shaft.

Vifaa kwa hatua hii:

Chombo cha kuhifadhi cha daraja la chakulaChombo cha kuhifadhi cha daraja la chakula1 kipande
Kizibo cha SilikoniKizibo cha Silikoni1 kipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara1 kipande
Washa bapaWasha bapa1 kipande
Ubao wa msonobariUbao wa msonobari1 kipande
Skrubu za mashineSkrubu za mashine1 kipande
Nati ya pembe sitaNati ya pembe sita1 kipande
Skrubu ya mti #8 x inchi 1Skrubu ya mti #8 x inchi 11 kipande

Zana zinazohitajika:

Seti ya misumeno ya duaraSeti ya misumeno ya duara
Kekee cha BetriKekee cha Betri
Seti ya vichimbuziSeti ya vichimbuzi
Msumeno wa mkonoMsumeno wa mkono
Seti ya bisibisiSeti ya bisibisi
Spana inayoweza kurekebishwaSpana inayoweza kurekebishwa
11

Shafts, fans and crank

Pass the hollow shaft up through the conical tube from below so the spur gear sits under the bottom, and glue the inner fan on its top just above the tube. Run a 10 mm stainless rod as the shaft G down through it, fix the shell gear on its foot with a set screw so the pinion on the stud meshes with both gears, and rest its end in the bridge's step. Bolt a pine bar F across the mouth as G's upper bearing; under it fix two hardwood blades reaching close to the tub's side as fan H, and above it a crank. A pine fork pivoted on the bridge, its handle pinned to the frame, holds the tub upright. Cut the container's lid in two, with a hole near the rim of one half as the aperture a'.

Vifaa kwa hatua hii:

Ufito wa chuma lainiUfito wa chuma laini1 kipande
Vijiti vya mbao ngumuVijiti vya mbao ngumu1 kipande
Ubao wa msonobariUbao wa msonobari1 kipande
Epoksi ya Sehemu MbiliEpoksi ya Sehemu Mbili1 kipande
Skrubu za mashineSkrubu za mashine1 kipande
Skrubu ya mti #8 x inchi 1Skrubu ya mti #8 x inchi 11 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha BetriKekee cha Betri
Seti ya vichimbuziSeti ya vichimbuzi
Seti ya bisibisiSeti ya bisibisi
Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
12

The build in 3D

FreeCAD model of this build, not of the patent: the conical tub cut away on its journals between the standards, the outer fan H, the conical tube K with the inner fan L on the hollow shaft above it, and under the bottom the shell gear, stud pinion and spur gear between the cross bar and bridge.
Faili ya UsanifuBLENDCC0 - Free
Pakua modeli
13

Churn, tip and work

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, fit both cover halves and crank steadily; time until the butter comes. Set a jug under the aperture, free the fork and tip the tub about 90 degrees onto its side, aperture down; crank on so the fans knead the butter while the buttermilk runs out. Stand it up, add cold water, churn a little, tip and drain again until the water runs clear; work in a pinch of salt the same way and weigh the butter.
Hatua 13 - Image 1

Vifaa kwa hatua hii:

Malai nzitoMalai nzito2000 ml
Chumvi ya Bahari MbichiChumvi ya Bahari Mbichi1 kipande
MajiMaji1 kipande

Zana zinazohitajika:

Kipima joto chenye kijiti kinachobaki ndaniKipima joto chenye kijiti kinachobaki ndani
Saa ya kupima mudaSaa ya kupima muda
Mizani ya dijitali ya jikoniMizani ya dijitali ya jikoni
Bakuli kubwa la kuchanganyia la chuma cha puaBakuli kubwa la kuchanganyia la chuma cha pua
14

Gears that jam, a tub that leaks

Tilting-tub counter-fan churn troubleshooting.

Flow

Loading...
15

History and honest limits

**Lucian A. Brown and Hubbard Bigelow** of Hartford, Connecticut, assignors to Henry K. W. Welch, received US 9,311, dated 5 October 1852; they signed the specification on 12 April 1852. They wrote that a cover is needed to stop the cream spattering, though the figure does not show it, and that working the butter in the tub saves lifting and the buttermilk. The ratio of 2 to 3, they wrote, was "a fact only learned by experiments, and corroborated by their repetition." They claimed the combination of the tub E and its appendages with the frame and standards, or any other frame adapted to use the tub in a vertical and a horizontal position. **Honest limits.** A container, pine and printed parts stand in for theirs; the gear sizes are ours. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.

Vifaa

15

Zana Zinazohitajika

13

Faili za muundo

6

Mchoro huu unatengeneza

Thumbnail
Kishikilia nafasi

Chombo cha kusukia siagi

Free

19
0

Blueprint zinazohusiana

Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni

Three-Shaft Geared Churn: Fans Above, Screw-Form Beaters Below, One Crank

Three-Shaft Geared Churn: Fans Above, Screw-Form Beaters Below, One Crank

na TheChefDK

CHAKULA NA VINYWAJI

29
0
0
0
0
0
Post-and-Float Butter-Working Churn: Floats Revolving Astride Fixed Posts

Post-and-Float Butter-Working Churn: Floats Revolving Astride Fixed Posts

na WoodyNO

Utengenezaji mbao

32
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation

Churning Butter from Cream — The 5,000-Year-Old Fat Separation

na TheChefDK

UJANJA

54
0
0
0
0
0

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...